- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX1180 (Maxim Integrated Products, Inc.) Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs PDF資料下載
參數資料
| 型號： | MAX1180 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| 中文描述： | 雙路、10位、105Msps、3.3V、低功耗ADC，內置電壓基準及并行輸出 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 573K |
| 代理商： | MAX1180 |
M
Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC
with Internal Reference and Parallel Outputs
______________________________________________________________________________________
11
Detailed Description
The MAX1180 uses a nine-stage, fully-differential
pipelined architecture (Figure 1), that allows for high-
speed conversion while minimizing power consump-
tion. Samples taken at the inputs move progressively
through the pipeline stages every half clock cycle.
Counting the delay through the output latch, the clock-
cycle latency is five clock cycles.
1.5-bit (two-comparator) flash ADCs convert the held-
input voltages into a digital code. The digital-to-analog
converters (DACs) convert the digitized results back
into analog voltages, which are then subtracted from
the original held-input signals. The resulting error sig-
nals are then multiplied by two and the residues are
passed along to the next pipeline stages where the
process is repeated until the signals have been
processed by all nine stages. Digital error correction
compensates for ADC comparator offsets in each of
these pipeline stages and ensures no missing codes.
Input Track-and-Hold (T/H) Circuits
Figure 2 displays a simplified functional diagram of the
input track-and-hold (T/H) circuits in both track-and-
hold mode. In track mode, switches S1, S2a, S2b, S4a,
S4b, S5a and S5b are closed. The fully-differential cir-
cuits sample the input signals onto the two capacitors
(C2a and C2b) through switches S4a and S4b. S2a and
S2b set the common mode for the amplifier input, and
open simultaneously with S1, sampling the input wave-
form. Switches S4a and S4b are then opened before
switches S3a and S3b, connect capacitors C1a and
C1b to the output of the amplifier, and switch S4c is
closed. The resulting differential voltages are held on
capacitors C2a and C2b. The amplifiers are used to
charge capacitors C1a and C1b to the same values
originally held on C2a and C2b. These values are then
presented to the first-stage quantizers and isolate the
pipelines from the fast-changing inputs. The wide input
bandwidth T/H amplifiers allow the MAX1180 to track-
and-sample/hold analog inputs of high frequencies
(> Nyquist). Both ADC inputs (INA+, INB+, INA-, and
INB-) can be driven either differentially or single-ended.
Match the impedance of INA+ and INA-, as well as
INB+ and INB-, and set the common-mode voltage to
midsupply (V
DD
/2) for optimum performance.
Analog Inputs and Reference
Configurations
The full-scale range of the MAX1180 is determined
by the internally generated voltage difference
between REFP (V
DD
/2 + V
REFIN
/4) and REFN (V
DD
/2 -
V
REFIN
/4).The full-scale range for both on-chip
T/H
V
OUT
x2
Σ
FLASH
ADC
DAC
1.5 BITS
10
V
INA
V
IN
STAGE 1
STAGE 2
D9A–D0A
V
INA
= INPUT VOLTAGE BETWEEN INA+ AND INA- (DIFFERENTIAL OR SINGLE-ENDED)
V
INB
= INPUT VOLTAGE BETWEEN INB+ AND INB- (DIFFERENTIAL OR SINGLE-ENDED)
DIGITAL CORRECTION LOGIC
STAGE 8
STAGE 9
2-BIT FLASH
ADC
T/H
T/H
V
OUT
x2
Σ
FLASH
ADC
DAC
1.5 BITS
10
V
INB
V
IN
STAGE 1
STAGE 2
D9B–D0B
DIGITAL CORRECTION LOGIC
STAGE 8
STAGE 9
2-BIT FLASH
ADC
T/H
Figure 1. Pipelined Architecture—Stage Blocks
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1180ECM | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1182 | Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183 | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183ECM | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1185 | Dual 10-Bit, 20Msps, +3V, Low-Power ADC with Internal Reference and Multiplexed Parallel Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11800ETC/V+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC/V+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800EVKIT+ | 功能描述:顯示開發工具 MAX11800 Eval Kit RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
發布緊急采購，3分鐘左右您將得到回復。