- 您現在的位置：買賣IC網 > PDF目錄383312 > MAX117MJI (MAXIM INTEGRATED PRODUCTS INC) +3V, 400ksps, 4/8-Channel, 8-Bit ADCs with 1UA Power-Down PDF資料下載
參數資料
| 型號： | MAX117MJI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | +3V, 400ksps, 4/8-Channel, 8-Bit ADCs with 1UA Power-Down |
| 中文描述： | 8-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP28 |
| 封裝： | 0.600 INCH, CERDIP-28 |
| 文件頁數： | 11/12頁 |
| 文件大小： | 106K |
| 代理商： | MAX117MJI |
If the analog input exceeds 50mV beyond the sup-
plies, limit the input current to no more than two
milliamperes, as excessive current will degrade the
conversion accuracy of the on channel.
Track/Hold
The track/hold enters hold mode when a conversion
starts (
RD
low or
WR
low). INT goes low at the end of
the conversion, at which point the track/hold enters
track mode. The next conversion can start after the
minimum acquisition time, t
ACQ
.
Transfer Function
Figure 10 shows the MAX113/MAX117’s nominal trans-
fer function. Code transitions occur halfway between
successive-integer LSB values. Output coding is binary
with 1LSB = (V
REF+
- V
REF-
) / 256.
Conversion Rate
The maximum sampling rate (f
MAX
) for the MAX113/
MAX117 is achieved in write-read mode (t
RD
< t
INTL
)
and is calculated as follows:
where t
WR
= the write pulse width, t
RD
= the delay
between write and read pulses, t
RI
=
RD
to
INT
delay,
and t
ACQ
= minimum acquisition time.
S ignal-to-Noise Ratio and
Effec tive Number of Bits
Signal-to-noise plus distortion (SINAD) is the ratio of the
fundamental input frequency’s RMS amplitude to all
other ADC output signals. The output spectrum is limit-
ed to frequencies above DC and below one-half the
ADC sample rate.
The theoretical minimum analog-to-digital noise is
caused by quantization error, and results directly from
the ADC’s resolution: SNR = (6.02N + 1.76)dB, where
N is the number of bits of resolution. Therefore, a per-
fect 8-bit ADC can do no better than 50dB.
The FFT Plot (see Typical Operating Characteristics)
shows the result of sampling a pure 30.27kHz sinusoid
at a 400kHz rate. This FFT plot of the output shows the
output level in various spectral bands.
The effective resolution (or “effective number of bits”)
the ADC provides can be measured by transposing the
equation that converts resolution to SNR: N = (SINAD -
1.76) / 6.02 (see Typical Operating Characteristics).
T otal Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of all harmonics of the input signal (in the frequen-
cy band above DC and below one-half the sample rate)
to the fundamental itself. This is expressed as:
where V
1
is the fundamental RMS amplitude, and V
2
through V
N
are the amplitudes of the 2nd through Nth
harmonics.
S purious-Free Dynamic Range
Spurious-free dynamic range (SFDR) is the ratio of the
fundamental RMS amplitude to the amplitude of the
next largest spectral component (in the frequency band
above DC and below one-half the sample rate). Usually
the next largest spectral component occurs at some
harmonic of the input frequency. However, if the ADC is
exceptionally linear, it may occur only at a random
peak in the ADC’s noise floor. See the Signal-to-Noise
Ratio graph in Typical Operating Characteristics.
THD = 20log
V
V
V
...V
V
2
2
3
2
4
2
N
2
1
+
+
+
f
=
1
t
+ t
+ t + t
f
=
1
+
600ns
800ns
300ns
450ns
f
465kHz
MAX
WR
RD
ACQ
MAX
MAX
+
+
=
M
+3V, 400ksps, 4/8-Channel,
8-Bit ADCs with 1μA Power-Down
______________________________________________________________________________________
11
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1180 | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1180ECM | Dual 10-Bit, 105Msps, +3.3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1182 | Dual 10-Bit, 65Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183 | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
| MAX1183ECM | Dual 10-Bit, 40Msps, +3V, Low-Power ADC with Internal Reference and Parallel Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11800ETC/V+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC/V+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+ | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800ETC+T | 功能描述:觸摸屏轉換器和控制器 SPI 4Ch Touch Screen Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MAX11800EVKIT+ | 功能描述:顯示開發工具 MAX11800 Eval Kit RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
發布緊急采購，3分鐘左右您將得到回復。