- 您現在的位置：買賣IC網 > PDF目錄10502 > MAX11647EUA+ (Maxim Integrated Products)IC ADC 10BIT I2C 94.4KSPS 8UMAX PDF資料下載
參數資料
| 型號： | MAX11647EUA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/22頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT I2C 94.4KSPS 8UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 10 |
| 采樣率（每秒）： | 94.4k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 362mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
MAX11646/MAX11647
Low-Power, 1-/2-Channel, I2C, 10-Bit ADCs
in Ultra-Tiny 1.9mm x 2.2mm Package
12
______________________________________________________________________________________
Single-Ended/Differential Input
The SGL/DIF of the configuration byte configures the
MAX11646/MAX11647 analog input circuitry for single-
ended or differential inputs (Table 2). In single-ended
mode (SGL/DIF = 1), the digital conversion results are
the difference between the analog input selected by
CS0 and GND (Table 3). In differential mode (SGL/
DIF = 0), the digital conversion results are the differ-
ence between the + and the - analog inputs selected
by CS0 (Table 4).
Unipolar/Bipolar
When operating in differential mode, the BIP/UNI bit of
the setup byte (Table 1) selects unipolar or bipolar
operation. Unipolar mode sets the differential input
range from 0 to VREF. A negative differential analog
input in unipolar mode causes the digital output code
to be zero. Selecting bipolar mode sets the differential
input range to ±VREF/2. The digital output code is bina-
ry in unipolar mode and two’s complement in bipolar
mode. See the
Transfer Functions section.
In single-ended mode, the MAX11646/MAX11647
always operate in unipolar mode irrespective of
BIP/UNI. The analog inputs are internally referenced to
GND with a full-scale input range from 0 to VREF.
2-Wire Digital Interface
The MAX11646/MAX11647 feature a 2-wire interface
consisting of a serial-data line (SDA) and serial-clock line
(SCL). SDA and SCL facilitate bidirectional communica-
tion between the MAX11646/MAX11647 and the master
at rates up to 1.7MHz. The MAX11646/MAX11647 are
slaves that transfer and receive data. The master (typi-
cally a microcontroller) initiates data transfer on the bus
and generates the SCL signal to permit that transfer.
SDA and SCL must be pulled high. This is typically done
with pullup resistors (750
Ω or greater) (see the Typical
Operating Circuit). Series resistors (RS) are optional.
They protect the input architecture of the MAX11646/
MAX11647 from high voltage spikes on the bus lines,
minimize crosstalk, and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. A minimum of 18 clock cycles are required to
transfer the data in or out of the MAX11646/
MAX11647. The data on SDA must remain stable dur-
ing the high period of the SCL clock pulse. Changes in
SDA while SCL is stable are considered control signals
(see the
START and STOP Conditions section). Both
SDA and SCL remain high when the bus is not busy.
START and STOP Conditions
The master initiates a transmission with a START condi-
tion (S), a high-to-low transition on SDA while SCL is high.
The master terminates a transmission with a STOP condi-
tion (P), a low-to-high transition on SDA while SCL is high
(Figure 5). A repeated START condition (Sr) can be used
in place of a STOP condition to leave the bus active and
the mode unchanged (see the
HS Mode section).
Acknowledge Bits
Data transfers are acknowledged with an acknowledge
bit (A) or a not-acknowledge bit (A). Both the master
and the MAX11646/MAX11647 (slave) generate
acknowledge bits. To generate an acknowledge, the
receiving device must pull SDA low before the rising
edge of the acknowledge-related clock pulse (ninth
pulse) and keep it low during the high period of the
clock pulse (Figure 6). To generate a not-acknowledge,
the receiver allows SDA to be pulled high before the
rising edge of the acknowledge-related clock pulse
and leaves SDA high during the high period of the
clock pulse. Monitoring the acknowledge bits allows for
detection of unsuccessful data transfers. An unsuc-
cessful data transfer happens if a receiving device is
busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master should
reattempt communication at a later time.
SCL
SDA
SP
Sr
Figure 5. START and STOP Conditions
SCL
SDA
S
NOT ACKNOWLEDGE
ACKNOWLEDGE
12
8
9
Figure 6. Acknowledge Bits
相關PDF資料 |
PDF描述 |
|---|---|
| MS3100E18-22P | CONN RCPT 3POS WALL MNT W/PINS |
| MAX11646EUA+ | IC ADC 10BIT I2C 94.4KSPS 8UMAX |
| VI-B0T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| MS3102A20-8S | CONN RCPT 6POS BOX MNT W/SCKT |
| VI-B0T-MX-F1 | CONVERTER MOD DC/DC 6.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11647EUA+ | 功能描述:模數轉換器 - ADC 12-Bit 2Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11647EUA+T | 功能描述:模數轉換器 - ADC 12-Bit 2Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11647EWC+T | 功能描述:模數轉換器 - ADC 12-Bit 2Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1165 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power, 16-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1165ACUI | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。