Low-Power, 4-/8-/12-Channel, I2C, 12-Bit ADCs in Ultra-Small P" />
參數資料
型號： MAX11615EEE+
廠商： Maxim Integrated Products
文件頁數： 3/24頁
文件大?。?/td> 0K
描述： IC ADC SERIAL 12BIT 8CH 16-QSOP
產品培訓模塊： MAX116xx
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 100
位數： 12
采樣率（每秒）： 94.4k
數據接口： I²C，串行
轉換器數目： 1
功率耗散（最大）： 666.7mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 管件
輸入數目和類型： 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極
產品目錄頁面： 1398 (CN2011-ZH PDF)
MAX11612–MAX11617
Low-Power, 4-/8-/12-Channel, I2C,
12-Bit ADCs in Ultra-Small Packages
11
Maxim Integrated
During the acquisition interval, the T/H switches are in
the track position and CT/H charges to the analog input
signal. At the end of the acquisition interval, the T/H
switches move to the hold position retaining the charge
on CT/H as a stable sample of the input signal.
During the conversion interval, the switched capacitive
DAC adjusts to restore the comparator input voltage to
0V within the limits of a 12-bit resolution. This action
requires 12 conversion clock cycles and is equivalent
to transferring a charge of 11pF (VIN+ - VIN-) from
CT/H to the binary weighted capacitive DAC, forming a
digital representation of the analog input signal.
Sufficiently low source impedance is required to ensure
an accurate sample. A source impedance of up to 1.5k
does not significantly degrade sampling accuracy. To
minimize sampling errors with higher source impedances,
connect a 100pF capacitor from the analog input to GND.
This input capacitor forms an RC filter with the source
impedance limiting the analog-input bandwidth. For larg-
er source impedances, use a buffer amplifier to maintain
analog-input signal integrity and bandwidth.
When operating in internal clock mode, the T/H circuitry
enters its tracking mode on the eighth rising clock edge
of the address byte, see the
Slave Address section. The
T/H circuitry enters hold mode on the falling clock edge of
the acknowledge bit of the address byte (the ninth clock
pulse). A conversion or a series of conversions is then
internally clocked and the MAX11612–MAX11617 holds
SCL low. With external clock mode, the T/H circuitry
enters track mode after a valid address on the rising
edge of the clock during the read (R/W = 1) bit. Hold
mode is then entered on the rising edge of the second
clock pulse during the shifting out of the first byte of the
result. The conversion is performed during the next 12
clock cycles.
The time required for the T/H circuitry to acquire an
input signal is a function of the input sample capaci-
tance. If the analog-input source impedance is high,
the acquisition time constant lengthens and more time
must be allowed between conversions. The acquisition
time (tACQ) is the minimum time needed for the signal
to be acquired. It is calculated by:
tACQ ≥ 9 (RSOURCE + RIN) CIN
where RSOURCE is the analog-input source impedance,
RIN = 2.5k, and CIN = 22pF. tACQ is 1.5/fSCL for internal
clock mode and tACQ = 2/fSCL for external clock mode.
Analog Input Bandwidth
The MAX11612–MAX11617 feature input-tracking circuit-
ry with a 5MHz small-signal bandwidth. The 5MHz input
bandwidth makes it possible to digitize high-speed tran-
sient events and measure periodic signals with band-
widths exceeding the ADC’s sampling rate by using
under sampling techniques. To avoid high-frequency
signals being aliased into the frequency band of interest,
anti-alias filtering is recommended.
Analog Input Range and Protection
Internal protection diodes clamp the analog input to
VDD and GND. These diodes allow the analog inputs to
TRACK
HOLD
CT/H
TRACK
HOLD
AIN0
AIN1
AIN2
AIN3/REF
GND
ANALOG INPUT MUX
CAPACITIVE
DAC
REF
CAPACITIVE
DAC
REF
MAX11612
MAX11613
HOLD
TRACK
HOLD
VDD/2
Figure 4. Equivalent Input Circuit
相關PDF資料
PDF描述
AD8328ACPZ IC LINE DRIVE CABLE 5V 20-LFCSP
AD8321ARZ-REEL IC LINE DVR CATV 20-SOIC T/R
MAX11614EEE+ IC ADC SERIAL 12BIT 8CH 16-QSOP
MAX11210EEE+ IC ADC 24BIT SPI/SRL 5SPS 16QSOP
MAX1111EEE+ IC ADC 8BIT LP 16-QSOP
相關代理商/技術參數
參數描述
MAX11615EEE+ 功能描述:模數轉換器 - ADC 12-Bit 8Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11615EEE+C78 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11615EEE+T 功能描述:模數轉換器 - ADC 12-Bit 8Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11615EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX11615 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX11615EVSYS+ 功能描述:數據轉換 IC 開發工具 MAX11615 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*