- 您現在的位置：買賣IC網 > PDF目錄10572 > MAX11615EEE+ (Maxim Integrated Products)IC ADC SERIAL 12BIT 8CH 16-QSOP PDF資料下載
參數資料
| 型號： | MAX11615EEE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC SERIAL 12BIT 8CH 16-QSOP |
| 產品培訓模塊： | MAX116xx Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 位數： | 12 |
| 采樣率（每秒）： | 94.4k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 666.7mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 產品目錄頁面： | 1398 (CN2011-ZH PDF) |
MAX11612–MAX11617
Low-Power, 4-/8-/12-Channel, I2C,
12-Bit ADCs in Ultra-Small Packages
18
Maxim Integrated
converted data is available immediately after the first
four empty high bits. The device continuously converts
input channels dictated by the scan mode until given a
not acknowledge. There is no need to readdress the
device with a read command to obtain new conversion
results (see Figure 11).
The conversion must complete in 1ms, or droop on the
track-and-hold capacitor degrades conversion results.
Use internal clock mode if the SCL clock period
exceeds 60s.
The MAX11612–MAX11617 must operate in external
clock mode for conversion rates from 40ksps to
94.4ksps. Below 40ksps, internal clock mode is recom-
mended due to much smaller power consumption.
Scan Mode
SCAN0 and SCAN1 of the configuration byte set the
scan mode configuration. Table 5 shows the scanning
configurations. If AIN_/REF is set to be a reference input
or output (SEL1 = 1, Table 6), AIN_/REF is excluded from
a multichannel scan. The scanned results are written to
memory in the same order as the conversion. Read the
results from memory in the order they were converted.
Each result needs a 2-byte transmission; the first byte
begins with four empty bits, during which SDA is left
high. Each byte has to be acknowledged by the master
or the memory transmission is terminated. It is not possi-
ble to read the memory independently of conversion.
Applications Information
Power-On Reset
The configuration and setup registers (Tables 1 and 2)
default to a single-ended, unipolar, single-channel con-
version on AIN0 using the internal clock with VDD as the
reference and AIN_/REF configured as an analog input.
The memory contents are unknown after power-up.
Automatic Shutdown
Automatic shutdown occurs between conversions when
the MAX11612–MAX11617 are idle. All analog circuits
participate in automatic shutdown except the internal
reference due to its prohibitively long wake-up time.
When operating in external clock mode, a STOP, not-
acknowledge, or repeated START condition must be
issued to place the devices in idle mode and benefit
from automatic shutdown. A STOP condition is not nec-
essary in internal clock mode to benefit from automatic
shutdown because power-down occurs once all con-
version results are written to memory (Figure 10). When
using an external reference or VDD as a reference, all
analog circuitry is inactive in shutdown and supply cur-
rent is less than 0.5A. The digital conversion results
obtained in internal clock mode are maintained in memo-
ry during shutdown and are available for access through
the serial interface at any time prior to a STOP or a
repeated START condition.
SCAN1
SCAN0
SCANNING CONFIGURATION
00
Scans up from AIN0 to the input selected by CS3–CS0. When CS3–CS0 exceeds 1011, the scanning
stops at AIN11. When AIN_/REF is set to be a REF input/output, scanning stops at AIN2 or AIN10.
0
1
*Converts the input selected by CS3–CS0 eight times (see Tables 3 and 4).
MAX11612/MAX11613: Scans upper half of channels.
Scans up from AIN2 to the input selected by CS1 and CS0. When CS1 and CS0 are set for AIN0, AIN1,
and AIN2, the only scan that takes place is AIN2 (MAX11612/MAX11613). When AIN/REF is set to be a
REF input/output, scanning stops at AIN2.
MAX11614/MAX11615: Scans upper quartile of channels.
Scans up from AIN6 to the input selected by CS3–CS0. When CS3–CS0 is set for AIN0–AIN6, the only
scan that takes place is AIN6 (MAX11614/MAX11615).
10
MAX11616/MAX11617: Scans upper half of channels.
Scans up from AIN6 to the input selected by CS3–CS0. When CS3–CS0 is set for AIN0–AIN6, the only
scan that takes place is AIN6 (MAX11616/MAX11617). When AIN/REF is set to be a REF input/output,
scanning stops at selected channel or AIN10.
1
*Converts channel selected by CS3–CS0.
*
When operating in external clock mode, there is no difference between SCAN[1:0] = 01 and SCAN[1:0] = 11, and converting occurs
perpetually until not-acknowledge occurs.
Table 5. Scanning Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| AD8328ACPZ | IC LINE DRIVE CABLE 5V 20-LFCSP |
| AD8321ARZ-REEL | IC LINE DVR CATV 20-SOIC T/R |
| MAX11614EEE+ | IC ADC SERIAL 12BIT 8CH 16-QSOP |
| MAX11210EEE+ | IC ADC 24BIT SPI/SRL 5SPS 16QSOP |
| MAX1111EEE+ | IC ADC 8BIT LP 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11615EEE+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11615EEE+C78 | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11615EEE+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11615EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX11615 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX11615EVSYS+ | 功能描述:數據轉換 IC 開發工具 MAX11615 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。