參數資料
型號: MAX11600EKA+T
廠商: Maxim Integrated Products
文件頁數: 5/23頁
文件大?。?/td> 0K
描述: IC ADC SERIAL 8BIT 4CH SOT23-8
產品培訓模塊: MAX116xx
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
位數: 8
采樣率(每秒): 188k
數據接口: I²C,串行
轉換器數目: 1
功率耗散(最大): 1.75mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: SOT-23-8
供應商設備封裝: SOT-23-8
包裝: 標準包裝
輸入數目和類型: 4 個單端,單極;4 個單端,雙極;2 個差分,單極;2 個差分,雙極
產品目錄頁面: 1398 (CN2011-ZH PDF)
其它名稱: MAX11600EKA+TDKR
Data Byte (Read Cycle)
A read cycle must be initiated to obtain conversion
results. Read cycles begin with the bus master issuing
a START condition followed by 7 address bits and a
read bit (R/W = 1). If the address byte is successfully
received, the MAX11600–MAX11605 (slave) issue an
acknowledge. The master then reads from the slave.
After the master has received the results, it can issue
an acknowledge if it wants to continue reading or a not
acknowledge if it no longer wishes to read. If the
MAX11600–MAX11605 receive a not acknowledge,
they release SDA, allowing the master to generate a
STOP or repeated START. See the
Clock Mode and
Scan Mode sections for detailed information on how
data is obtained and converted.
Clock Mode
The clock mode determines the conversion clock, the
acquisition time, and the conversion time. The clock
mode also affects the scan mode. The state of the
setup byte’s CLK bit determines the clock mode (Table
1). At power-up, the MAX11600–MAX11605 default to
internal clock mode (CLK = zero).
Internal Clock
When configured for internal clock mode (CLK = zero),
the MAX11600–MAX11605 use their internal oscillator
as the conversion clock. In internal clock mode, the
MAX11600–MAX11605 begin tracking analog input on
the ninth falling clock edge of a valid slave address
byte. Two internal clock cycles later, the analog signal
is acquired and the conversion begins. While tracking
and converting the analog input signal, the
MAX11600–MAX11605 hold SCL low (clock stretching).
After the conversion completes, the results are stored in
MAX11600–MAX11605
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
______________________________________________________________________________________
13
110
1
00
0
R/W
A
SLAVE ADDRESS
S
SCL
SDA
1
234
567
89
DEVICE
SLAVE ADDRESS
1100100
1101101
MAX11600/MAX11601
MAX11602/MAX11603
1100101
MAX11604/MAX11605
Figure 7. Slave Address Byte
000
1
0X
X
A
HS MODE MASTER CODE
SCL
SDA
S
Sr
F/S MODE
HS MODE
Figure 8. F/S Mode to HS Mode Transfer
相關PDF資料
PDF描述
MAX11662AUB+T IC ADC 8BIT SRL 500KSPS 10UMAX
SP3232EBCN-L IC TXRX RS232 ESD TRUE 16NSOIC
TW8816-BA3-GRS IC LCD CTRLR 144TFBGA
TW8816-LB3-CR IC TFT LCD CTRLR W/MCU 128-LQFP
PX0707/P/09 CONN RCPT 9POS W/PINS PCB
相關代理商/技術參數
參數描述
MAX11601 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
MAX11601EKA+ 制造商:Maxim Integrated Products 功能描述:2.7V TO 3.6V AND 4.5V TO 5.5V, LOW-POWER,4-/8-/12-CHANNEL - Rail/Tube
MAX11601EKA+T 功能描述:模數轉換器 - ADC 8-Bit 4Ch 188ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11602 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
MAX11602EEE+ 功能描述:模數轉換器 - ADC 8-Bit 8Ch 188ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32