參數資料
型號： MAX11600EKA+T
廠商： Maxim Integrated Products
文件頁數： 3/23頁
文件大?。?/td> 0K
描述： IC ADC SERIAL 8BIT 4CH SOT23-8
產品培訓模塊： MAX116xx
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
位數： 8
采樣率（每秒）： 188k
數據接口： I²C，串行
轉換器數目： 1
功率耗散（最大）： 1.75mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： SOT-23-8
供應商設備封裝： SOT-23-8
包裝： 標準包裝
輸入數目和類型： 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極
產品目錄頁面： 1398 (CN2011-ZH PDF)
其它名稱： MAX11600EKA+TDKR
Single-Ended/Pseudo-Differential Input
The SGL/DIF bit of the configuration byte configures the
MAX11600–MAX11605 analog input circuitry for single-
ended or pseudo-differential inputs (Table 2). In single-
ended mode (SGL/DIF = 1), the digital conversion results
are the difference between the analog input selected by
CS[3:0] and GND (Table 3). In pseudo-differential mode
(SGL/DIF = 0), the digital conversion results are the differ-
ence between the positive and the negative analog inputs
selected by CS[3:0] (Table 4). The negative analog input
signal must remain stable within ±0.5 LSB (±0.1 LSB for
best results) with respect to GND during a conversion.
Unipolar/Bipolar
When operating in pseudo-differential mode, the BIP/
UNI bit of the setup byte (Table 1) selects unipolar or
bipolar operation. Unipolar mode sets the differential
analog input range from zero to VREF. A negative differ-
ential analog input in unipolar mode causes the digital
output code to be zero. Selecting bipolar mode sets the
differential input range to ±VREF/2, with respect to the
negative input. The digital output code is binary in
unipolar mode and two’s complement binary in bipolar
mode (see the
Transfer Functions section).
In single-ended mode, the MAX11600–MAX11605
always operate in unipolar mode regardless of the
BIP/UNI setting, and the analog inputs are internally ref-
erenced to GND with a full-scale input range from zero
to VREF.
Digital Interface
The MAX11600–MAX11605 feature a 2-wire interface
consisting of a serial-data line (SDA) and a serial-clock
line (SCL). SDA and SCL facilitate bidirectional communi-
cation between the MAX11600–MAX11605 and the mas-
ter at rates up to 1.7MHz. The MAX11600–MAX11605 are
slaves that transmit and receive data. The master (typical-
ly a microcontroller) initiates data transfer on the bus and
generates SCL to permit that transfer.
SDA and SCL must be pulled high. This is typically
done with pullup resistors (500
or greater) (see
Typical Operating Circuit). Series resistors (RS) are
optional. They protect the input architecture of the
MAX11600–MAX11605 from high-voltage spikes on the
bus lines and minimize crosstalk and undershoot of the
bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. Nine clock cycles are required to transfer the
data in or out of the MAX11600–MAX11605. The data
on SDA must remain stable during the high period of
the SCL clock pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
Conditions section). Both SDA and SCL idle high when
the bus is not busy.
START and STOP Conditions
The master initiates a transmission with a START condi-
tion (S), a high-to-low transition on SDA with SCL high.
The master terminates a transmission with a STOP
condition (P), a low-to-high transition on SDA, while
MAX11600–MAX11605
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
______________________________________________________________________________________
11
BIT 7
(MSB)
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(LSB)
REG
SEL2
SEL1
SEL0
CLK
BIP/
UNI
RST
X
BIT
NAME
DESCRIPTION
7
REG
Register bit. 1 = setup byte, 0 = configuration byte (Table 2).
6
SEL2
5
SEL1
4
SEL0
Three bits select the reference voltage and the state of AIN_/REF
(MAX11600/MAX11601/MAX11604/MAX11605) or REF (MAX11602/MAX11603) (Table 6).
Default to 000 at power-up.
3
CLK
1 = external clock, 0 = internal clock. Defaulted to zero at power-up.
2
BIP/
UNI
1 = bipolar, 0 = unipolar. Defaulted to zero at power-up (see the Unipolar/Bipolar section).
1
RST
1 = no action, 0 = resets the configuration register to default. Setup register remains unchanged.
0
X
Don’t care; can be set to 1 or 0.
Table 1. Setup Byte Format
相關PDF資料
PDF描述
MAX11662AUB+T IC ADC 8BIT SRL 500KSPS 10UMAX
SP3232EBCN-L IC TXRX RS232 ESD TRUE 16NSOIC
TW8816-BA3-GRS IC LCD CTRLR 144TFBGA
TW8816-LB3-CR IC TFT LCD CTRLR W/MCU 128-LQFP
PX0707/P/09 CONN RCPT 9POS W/PINS PCB
相關代理商/技術參數
參數描述
MAX11601 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
MAX11601EKA+ 制造商:Maxim Integrated Products 功能描述:2.7V TO 3.6V AND 4.5V TO 5.5V, LOW-POWER,4-/8-/12-CHANNEL - Rail/Tube
MAX11601EKA+T 功能描述:模數轉換器 - ADC 8-Bit 4Ch 188ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX11602 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/8-/12-Channel 2-Wire Serial 8-Bit ADCs
MAX11602EEE+ 功能描述:模數轉換器 - ADC 8-Bit 8Ch 188ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*