- 您現在的位置：買賣IC網 > PDF目錄9886 > MAX1142BCAP+ (Maxim Integrated Products)IC ADC 14BIT 200KSPS 20-SSOP PDF資料下載
參數資料
| 型號： | MAX1142BCAP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 200KSPS 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 66 |
| 位數： | 14 |
| 采樣率（每秒）： | 200k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 640mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
MAX1142/MAX1143
14-Bit ADC, 200ksps, +5V Single-Supply
with Reference
______________________________________________________________________________________
13
Data Framing
The falling edge of
CS does NOT start a conversion on
the MAX1142/MAX1143. The first logic high clocked
into DIN is interpreted as a start bit and defines the first
bit of the Control-Byte. A conversion starts on the falling
edge of SCLK, after the seventh bit of the Control-Byte
(the P1 bit) is clocked into DIN. The start bit is defined
as:
The first high bit clocked into DIN with
CS low, any-
time the converter is idle, e.g. after AVDD is applied,
or as the first high bit clocked into DIN after
CS is
pulsed high, then low.
OR
If a falling edge on
CS forces a start bit before the
conversion or calibration is complete, then the cur-
rent operation will be terminated and a new one
started.
Applications Information
Power-On Reset
When power is first applied to the MAX1142/MAX1143
or if
RST is pulsed low, the internal calibration registers
are set to their default values. The user-programmable
registers (P0, P1 and P2) are low, and the device is
configured for bipolar mode with internal clocking.
Calibration
To compensate the MAX1142/MAX1143 for tempera-
ture drift and other variations, they should be periodi-
cally calibrated. After any change in ambient
temperature more than 10°C, the device should be
recalibrated. A 100mV change in supply voltage or any
change in the reference voltage should be followed by
a calibration. Calibration corrects for errors in gain, off-
set, integral nonlinearity and differential nonlinearity.
The MAX1142/MAX1143 should be calibrated after
power-up or the assertion of reset. Make sure the
power supplies and the reference voltage have fully
settled prior to initiating the calibration sequence.
Initiate calibration by setting M1 = 0 and M0 = 1 in the
Control-Byte. In internal clock mode, SSTRB goes low
at the beginning of calibration and goes high to signal
the end of calibration, approximately 80,000 clock
cycles later. In external clock mode, SSTRB goes high
at the beginning of calibration and goes low to signal
the end of calibration. Calibration should be performed
in the same clock mode as will be used for conversions
(Figure 6).
Reference
The MAX1142/MAX1143 can be used with an internal or
external reference. An external reference can be con-
nected directly at the REF pin or at the REFADJ pin.
CREF is an internal reference node and must be
bypassed with a 1F capacitor when using either the
internal or an external reference.
Internal Reference
When using the MAX1142/MAX1143’s internal refer-
ence, place a 0.22F ceramic capacitor from REFADJ
to AGND and place a 2.2F capacitor from REF to
AGND. Fine adjustments can be made to the internal
reference voltage by sinking or sourcing current at
REFADJ. The input impedance of REFADJ is nominally
9k
. The internal reference voltage is adjustable to
±1.5% with the circuit of Figure 7.
tSDV
tSSTRB
tSTR
P1 CLOCKED IN
SSTRB
SCLK
CS
Figure 6. External Clock Mode SSTRB Detailed Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467T19B11SD | CONN PLUG 11POS STRAIGHT W/SCKT |
| MS27467T19B11SB | CONN PLUG 11POS STRAIGHT W/SCKT |
| MS27468T25A61P | CONN RCPT 61POS JAM NUT W/PINS |
| MS27473E16A99PA | CONN PLUG 23POS STRAIGHT W/PINS |
| D38999/26WE99PC | CONN PLUG 23POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1142BCAP+ | 功能描述:模數轉換器 - ADC 14-Bit 200ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1142BCAP+T | 功能描述:模數轉換器 - ADC 14-Bit 200ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1142BCAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1142BEAP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1142BEAP+ | 功能描述:模數轉換器 - ADC 14-Bit 200ksps 4.2V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。