- 您現在的位置：買賣IC網 > PDF目錄9500 > MAX11359AETL+ (Maxim Integrated Products)IC DAS SYSTEM 16BIT 40-TQFN PDF資料下載
參數資料
| 型號： | MAX11359AETL+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 29/67頁 |
| 文件大小： | 0K |
| 描述： | IC DAS SYSTEM 16BIT 40-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 數據采集系統（DAS） |
| 分辨率（位）： | 16 b |
| 采樣率（每秒）： | 512 |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-TQFN-EP（6x6） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
MAX11359A
16-Bit Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
35
Maxim Integrated
The ADC register configures the ADC and starts
a conversion.
ADCE: ADC power-enable bit. ADCE = 1 powers up
the ADC, and ADCE = 0 powers down the ADC.
STRT: ADC start bit. STRT = 1 resets the registers
inside the ADC filter and initiates a conversion or cali-
bration. The conversion begins immediately after the
16th ADC control bit is clocked by the rising edge of
SCLK. The initial conversion requires four conversion
cycles for valid output data. If CONT = 0 when STRT is
asserted, the ADC stops after a single conversion and
holds the result in the DATA register. If CONT = 1 when
STRT is asserted, the ADC performs continuous conver-
sions at the rate specified by the RATE<2:0> bits until
CONT is deasserted or ADCE is deasserted, powering
down the ADC. The STRT bit is automatically deasserted
after the initial conversion is complete (four conversion
cycles; the ADC status bit ADD in the STATUS register
asserts.) The current ADC configurations are not affect-
ed if the ADC register is written with STRT = 0. This
allows the ADC and mux configurations to be updated
simultaneously with the S bit in the MUX register.
BIP: Unipolar/bipolar bit. Set BIP = 0 for unipolar mode
and BIP = 1 for bipolar mode. Unipolar-mode data is
unsigned binary format and bipolar is two’s complement.
See the
ADC Transfer Functions section for more details.
POL: Polarity flipper bit. POL = 1 flips the polarity of the
differential signal to the ADC and the input to the signal-
detect comparator (SDC). POL = 0 sets the positive mux
output to the positive ADC and SDC inputs, and the neg-
ative mux output to the negative ADC and SDC inputs.
POL = 1 sets the positive mux output to the negative
ADC and SDC inputs, and the negative mux output to
the positive ADC and SDC inputs.
CONT: Continuous conversion bit. CONT = 1 enables
continuous conversions following completion of the first
conversion or calibration(s) initiated by the STRT or S
bit. Set CONT = 0 while asserting the STRT bit, or prior
to asserting the S bit to perform a single conversion or to
prevent conversions following a calibration. Set CONT =
0 to abort continuous conversions already in progress.
When the ADC is stopped in this way, the last complete
conversion result remains in the DATA register and the
internal ADC state information is lost. Asserting the
CONT bit does not restart the ADC, but results in contin-
uous conversions once the ADC is restarted with the
STRT or S bit.
ADCREF: ADC reference source bit. Set ADCREF = 0
to select REF as the ADC reference. Set ADCREF = 1
to select AVDD as the ADC reference. To measure the
AVDD voltage without having to attenuate the supply
voltage, select REF and AGND as the differential inputs
to the ADC, with POL = 0 and while ADCREF = 1.
GAIN<1:0>: ADC gain-setting bits. These two bits
select the gain of the ADC as shown in Table 5.
MSB
LSB
ADCE
STRT
BIP
POL
CONT
ADCREF
GAIN<1:0>
RATE<2:0>
MODE<2:0>
X
ADC Register (Power-On State: 0000 0000 0000 00XX)
Register Bit Descriptions
GAIN SETTING (V/V)
GAIN1
GAIN0
10
0
20
1
41
0
81
1
Table 5. Setting the Gain of the ADC
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474T8B98P | CONN RCPT 3POS JAM NUT W/PINS |
| MAX1409CAP+ | IC DAS 16BIT LP 20-SSOP |
| V110A28M300BL2 | CONVERTER MOD DC/DC 28V 300W |
| NBXDBA014LN1TAG | IC CLK XO 62.5/125MHZ 6CLCC |
| MS27508E16B6PA | CONN RCPT 6POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11359AETL+ | 功能描述:模數轉換器 - ADC 16-Bit DAS w/ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11359AETL+T | 功能描述:模數轉換器 - ADC 16-Bit DAS w/ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11359AETL-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1135BCAP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1135BCAP+ | 功能描述:模數轉換器 - ADC 16-Bit 150ksps 3.3V Single Supply RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。