- 您現在的位置：買賣IC網 > PDF目錄17007 > MAX1132EVKIT (Maxim Integrated Products)KIT EVAL FOR MAX1132 PDF資料下載
參數資料
| 型號： | MAX1132EVKIT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL FOR MAX1132 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 200k |
| 數據接口： | 串行 |
| 輸入范圍： | ±12 V |
| 在以下條件下的電源（標準）： | 55mW @ 200kSPS |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX1132，MAX1133 |
| 已供物品： | 板，CD |
Operating Modes and Serial Interfaces
The MAX1132/MAX1133 are fully compatible with
MICROWIRE and SPI/QSPI devices. MICROWIRE and
SPI/QSPI both transmit a byte and receive a byte at the
same time. The simplest software interface requires
only three 8-bit transfers to perform a conversion (one
8-bit transfer to configure the ADC, and two more 8-bit
transfers to clock out the 16-bit conversion result).
Short Acquisition Mode (24 SCLK)
Configure short acquisition by setting M1 = 0 and M0 =
0. In short acquisition mode, the acquisition time is 5.5
clock cycles. The total period is 24 clock cycles per
conversion.
Mode 2 Long Acquisition Mode (32 SCLK)
Configure long acquisition by setting M1 = 1 and M0 =
1. In long acquisition mode, the acquisition time is 13.5
clock cycles. The total period is 32 clock cycles per
conversion.
Calibration Mode
A calibration is initiated through the serial interface by
setting M1 = 0, M0 = 1. Calibration can be done in
either internal or external clock mode, though it is desir-
able that the part be calibrated in the same mode in
which it will be used to do conversions. The part will
remain in calibration mode for approximately 80,000
clock cycles unless the calibration is aborted.
Calibration is halted if
RST or SHDN goes low, or if a
valid start condition occurs.
Software Shutdown
A software power-down is initiated by setting M1 = 1,
M0 = 0. After the conversion completes, the part shuts
down. It reawakens upon receiving a new start bit.
Conversions initiated with M1 = 1 and M0 = 0 (shut-
down) use the acquisition mode selected for the previ-
ous conversion.
Shutdown Mode
The MAX1132/MAX1133 may be shut down by pulling
SHDN low or by asserting software shutdown. In addi-
tion to lowering power dissipation to 13W, consider-
able power can be saved by shutting down the
converter for short periods (duration will be affected by
REF startup time with internal reference) between con-
versions. There is no need to perform a calibration after
the converter has been shut down, unless the time in
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________
15
4
7
6
2
3
IN
+15V
-15V
0.0033F
0.1F
100pF
1k
20
AIN
MAX427
ELANTEC
EL2003
Figure 8. AIN Buffer for AC/DC Use
4
7
6
2
3
IN
+5V
-5V
AIN
0.1F
22
510
MAX410
Figure 9. ±5V Buffer for AC/DC Use Has ±3.5V Swing
相關PDF資料 |
PDF描述 |
|---|---|
| HCM10DRTI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| AC2626K4 | PROBE TEMP 4" GENERAL PURP |
| HBM10DRTI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| 0210490252 | CABLE JUMPER 1.25MM .254M 18POS |
| ADZS-AUDIO-EX3 | BOARD EXTENDER AUDIO EI3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1132EVSYS | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation System for the MAX1132/MAX1133 |
| MAX1132-MAX1133 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit ADC, 200ksps, 5V Single-Supply with Reference |
| MAX1133 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit ADC, 200ksps, 5V Single-Supply with Reference |
| MAX11330 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3Msps, 12-/10-Bit, 8-/16-Channel ADCs with Post-Mux External Signal Conditioning Access |
| MAX11330ATJ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3Msps, 12-/10-Bit, 8-/16-Channel ADCs with Post-Mux External Signal Conditioning Access |
發布緊急采購，3分鐘左右您將得到回復。