- 您現在的位置：買賣IC網 > PDF目錄10570 > MAX11101EUB+T (Maxim Integrated Products)IC ADC 14BIT SRL 200KSPS 10UMAX PDF資料下載
參數資料
| 型號： | MAX11101EUB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT SRL 200KSPS 10UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 200k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 444mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-uMAX |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 1 個單端，單極 |
| 其它名稱： | MAX11101EUB+TDKR |
Maxim Integrated Products 17
MAX11101
14-Bit, +5V, 200ksps ADC with 10A Shutdown
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-fit straight line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. The static
linearity parameters for the MAX11101 are measured
using the endpoint method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1 LSB. A DNL
error specification of 1 LSB guarantees no missing codes
and a monotonic transfer function.
Aperture Definitions
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between samples. Aperture delay (tAD) is the
time between the falling edge of the sampling clock and
the instant when the actual sample is taken.
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital
samples, signal-to-noise ratio (SNR) is the ratio of the
full-scale analog input (RMS value) to the RMS quantiza-
tion error (residual error). The ideal, theoretical minimum
analog-to-digital noise is caused by quantization noise
error only and results directly from the ADCs resolution
(N bits):
SNR = (6.02 x N + 1.76)dB
In reality, there are other noise sources besides quantiza-
tion noise: thermal noise, reference noise, clock jitter, etc.
SNR is computed by taking the ratio of the RMS signal to
the RMS noise, which includes all spectral components
minus the fundamental, the first five harmonics, and the
DC offset.
Signal-to-Noise Plus Distortion
Signal-to-noise plus distortion (SINAD) is the ratio of the
fundamental input frequency’s RMS amplitude to the
RMS equivalent of all the other ADC output signals.
(
)
RMS
Signal
SINAD(dB) 20 log
Noise Distortion
=
×
+
Effective Number of Bits
Effective number of bits (ENOB) indicate the global
accuracy of an ADC at a specific input frequency and
sampling rate. An ideal ADC error consists of quantiza-
tion noise only. With an input range equal to the full-scale
range of the ADC, calculate the effective number of bits
as follows:
ENOB = (SINAD – 1.76)/6.02
Figure 13 shows the effective number of bits as a function
of the MAX11101’s input frequency.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of the first five harmonics of the input signal to the
fundamental itself. This is expressed as:
2
22
234
5
VV
V
THD 20 log
V1
++
+
=
×
where V1 is the fundamental amplitude and V2 through
V5 are the 2nd- through 5th-order harmonics.
Spurious-Free Dynamic Range
Spurious-free dynamic range (SFDR) is the ratio of the
RMS amplitude of the fundamental (maximum signal
component) to the RMS value of the next largest fre-
quency component.
Figure 13. Effective Number of Bits vs. Input Frequency
0.1
10
100
MAX11101
Fig13
INPUT FREQUENCY (kHz)
EFFECTIVE
NUMBER
OF
BITS
1
14
0
2
4
6
8
12
10
fSAMPLE = 200kHz
相關PDF資料 |
PDF描述 |
|---|---|
| SP3244EEY-L | IC TXRX RS232 28TSSOP |
| SP3244EEA-L | IC TXRX RS232 28SSOP |
| MS3102R20-17P | CONN RCPT 6POS BOX MNT W/PINS |
| MAX11101EWC+T | IC ADC 14BIT SRL 200KSPS 12WLP |
| MS3102R20-19PW | CONN RCPT 3POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11101EWC | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:14-Bit, +5V, 200ksps ADC with 10μA Shutdown |
| MAX11101EWC+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:14-Bit, 5V, 200ksps ADC with 10??A Shutdown |
| MAX11101EWC+T | 功能描述:模數轉換器 - ADC 14-Bit 5V 200ksps w/10uA Shutdown RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11102 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs |
| MAX11102_11 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2Msps/3Msps, Low-Power, Serial 12-/10-/8-Bit ADCs 2.2V to 3.6V Supply Voltage |
發布緊急采購，3分鐘左右您將得到回復。