參數資料
型號: MA4E1319-2
元件分類: 射頻混頻器
英文描述: GALLIUM ARSENIDE, mm WAVE BAND, MIXER DIODE
封裝: CASE 1200, FLIP CHIP-3
文件頁數: 4/7頁
文件大?。?/td> 134K
代理商: MA4E1319-2
4
GaAs Flip Chip Schottky Barrier Diodes
M/A-COM Products
Rev. V5
MA4E1317, MA4E1318, MA4E1319-1,
MA4E1319-2, MA4E2160
ADVANCED: Data Sheets contain information regarding a product MA-COM Technical Solutions
is considering for development. Performance is based on target specifications, simulated results,
and/or prototype measurements. Commitment to develop is not guaranteed.
PRELIMINARY: Data Sheets contain information regarding a product MA-COM Technical
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be avail-
able. Commitment to produce in volume is not guaranteed.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.
MA-COM Technical Solutions and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice.
Mounting Techniques
These chips were designed to be inserted onto hard or soft substrates with the junction side down. They can be
mounted with conductive epoxy or with a low temperature solder preform. The die can also be assembled with
the junction side up, and wire or ribbon bonds made to the pads.
Solder Die Attach:
Solder which does not scavenge gold, such as Indalloy # 2, is recommended. Sn-Pb based solders are not rec-
ommended due to solder embrittlement. Do not expose die to a temperature greater than 235°C, or greater than
200°C for longer than 10 seconds. No more than three seconds of scrubbing should be required for attachment.
Epoxy Die Attach:
Assembly can be preheated to 125 - 150°C. Use a minimum amount of epoxy. Cure epoxy as per manufac-
turer’s schedule. For extended cure times, temperatures should be kept below 200°C.
Handling Procedures
The following precautions should be observed to avoid damaging these chips:
Cleanliness:
The chips should be handled in a clean environment.
Do not attempt to clean die after installation.
Static Sensitivity: Schottky barrier diodes are ESD sensitive and can be damaged by static
electricity. Proper ESD techniques should be used when handling these devices.
General Handling: The protective polymer coating on the active areas of these die provides scratch
protection, particularly for the metal air bridge which contacts the anode. Die can
be handled with tweezers or vacuum pickups and are suitable for use with
automatic pick-and-place equipment.
相關PDF資料
PDF描述
MA4E2160 GALLIUM ARSENIDE, mm WAVE BAND, MIXER DIODE
MA4E2508M-1112T SILICON, MEDIUM BARRIER SCHOTTKY, KU BAND, MIXER DIODE
MA4P606-255 SILICON, PIN DIODE
MA4P803 100 V, SILICON, PIN DIODE
MA4ST079-287T LF-UHF BAND, 54.1 pF, 12 V, SILICON, HYPERABRUPT VARIABLE CAPACITANCE DIODE
相關代理商/技術參數
參數描述
MA4E1338 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Silicon Medium Barrier Schottky Diodes
MA4E1338_V7 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Silicon Medium Barrier Schottky Diodes
MA4E1338A1-1141T 功能描述:肖特基二極管與整流器 RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
MA4E1338A1-1146T 功能描述:肖特基二極管與整流器 RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel
MA4E1338A-1141 制造商:M/A-COM Technology Solutions 功能描述:SCHOTTKY 8V 0.03A 2PIN SOD-323 - Bulk