- 您現在的位置：買賣IC網 > PDF目錄383303 > M50LPW116 (意法半導體) 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory PDF資料下載
參數資料
| 型號： | M50LPW116 |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| 中文描述： | 16兆位的2Mb × 8，啟動塊3V電源低引腳數快閃記憶體 |
| 文件頁數： | 14/36頁 |
| 文件大?。?/td> | 259K |
| 代理商： | M50LPW116 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
M50LPW116
14/36
Table 13. Status Register Bits
Note: 1.
For Program operations during Erase Suspend Bit 6 is ‘1’, otherwise Bit 6 is ‘0’.
Operation
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Program active
‘0’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘0’
Program suspended
‘1
X
(1)
‘0’
‘0’
‘0’
‘1’
‘0’
Program completed successfully
‘1’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘0’
Program failure due to V
PP
Error
‘1’
X
(1)
‘0’
‘0’
‘1’
‘0’
‘0’
Program failure due to Block Protection (LPC Interface only)
‘1’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘1’
Program failure due to cell failure
‘1’
X
(1)
‘0’
‘1’
‘0’
‘0’
‘0’
Erase active
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Block Erase suspended
‘1’
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase completed successfully
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase failure due to V
PP
Error
‘1’
‘0’
‘0’
‘0’
‘1’
‘0’
‘0’
Block Erase failure due to Block Protection (LPC Interface
only)
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
‘1’
Erase failure due to failed cell(s)
‘1’
‘0’
‘1’
‘0’
‘0’
‘0’
‘0’
Sequence command error
‘1’
‘0’
‘1’
‘1’
‘0’
‘0’
‘0’
Program/Erase Suspend has paused it. One Bus
Write cycle is required to issue the Program/Erase
Resume command. Once the command is issued
subsequent Bus Read operations read the Status
Register.
STATUS REGISTER
The Status Register provides information on the
current or previous Program or Erase operation.
Different bits in the Status Register convey
different information and errors on the operation.
To read the Status Register the Read Status
Register command can be issued. The Status
Register is automatically read after Program,
Erase and Program/Erase Resume commands
are issued. The Status Register can be read from
any address.
The Status Register bits are summarized in Table
13, Status Register Bits. Refer to Table 13 in con-
junction with the text descriptions below.
Program/Erase Controller Status (Bit 7).
The Pro-
gram/Erase Controller Status bit indicates whether
the Program/Erase Controller is active or inactive.
When the Program/Erase Controller Status bit is
‘0’, the Program/Erase Controller is active; when
the bit is ‘1’, the Program/Erase Controller is inac-
tive.
The Program/Erase Controller Status is ‘0’ imme-
diately after a Program/Erase Suspend command
is issued until the Program/Erase Controller paus-
es. After the Program/Erase Controller pauses the
bit is ‘1’.
During Program and Erase operation the Pro-
gram/Erase Controller Status bit can be polled to
find the end of the operation. The other bits in the
Status Register should not be tested until the Pro-
gram/Erase Controller completes the operation
and the bit is ‘1’.
After the Program/Erase Controller completes its
operation the Erase Status, Program Status, V
PP
Status and Block Protection Status bits should be
tested for errors.
Erase Suspend Status (Bit 6).
The Erase Sus-
pend Status bit indicates that a Block Erase oper-
ation has been suspended and is waiting to be
resumed. The Erase Suspend Status should only
be considered valid when the Program/Erase
Controller Status bit is ‘1’ (Program/Erase Control-
ler inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Erase Suspend Status bit is ‘0’ the Pro-
gram/Erase Controller is active or has completed
its operation; when the bit is ‘1’ a Program/Erase
Suspend command has been issued and the
memory is waiting for a Program/Erase Resume
command.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns to ‘0’.
相關PDF資料 |
PDF描述 |
|---|---|
| M50LPW116N | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N1T | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N5T | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M51131L | 2 CHANNEL ELECTRONIC VOLUME BALANCE |
| M51354AP | TV IF SYSTEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50LPW116N | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N1 | 功能描述:閃存 3.0V 16M (2Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50LPW116N1T | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL/SERL 3V/3.3V 16MBIT 2MX8 40TSOP - Tape and Reel |
| M50LPW116N5G | 功能描述:閃存 16 MBIT 3V SUPPLY RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50LPW116N5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。