- 您現在的位置：買賣IC網 > PDF目錄383303 > M50FW040NB5P (意法半導體) 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory PDF資料下載
參數資料
| 型號： | M50FW040NB5P |
| 廠商： | 意法半導體 |
| 英文描述： | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| 中文描述： | 4兆位（512 KB的× 8，均勻塊）3 - V電源供電的閃存固件樞紐 |
| 文件頁數： | 19/53頁 |
| 文件大?。?/td> | 278K |
| 代理商： | M50FW040NB5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
M50FW040
Bus operations
19/53
3.2
Address/Address multiplexed (A/A Mux) bus operations
The Address/Address Multiplexed (A/A Mux) Interface has a more traditional style interface.
The signals consist of a multiplexed address signals (A0-A10), data signals, (DQ0-DQ7) and
three control signals (RC, G, W). An additional signal, RP, can be used to reset the memory.
The Address/Address Multiplexed (A/A Mux) Interface is included for use by Flash
Programming equipment for faster factory programming. Only a subset of the features
available to the Firmware Hub (FWH) Interface are available; these include all the
Commands but exclude the Security features and other registers.
The following operations can be performed using the appropriate bus cycles: Bus Read, Bus
Write, Output Disable and Reset.
When the Address/Address Multiplexed (A/A Mux) Interface is selected all the blocks are
unprotected. It is not possible to protect any blocks through this interface.
3.2.1
Bus Read
Bus Read operations are used to output the contents of the Memory Array, the Electronic
Signature and the Status Register. A valid Bus Read operation begins by latching the Row
Address and Column Address signals into the memory using the Address Inputs, A0-A10,
and the Row/Column Address Select RC. Then Write Enable (W) and Interface Reset (RP)
must be High, V
IH
, and Output Enable, G, Low, V
IL
, in order to perform a Bus Read
operation. The Data Inputs/Outputs will output the value, see
Figure 13
, and
Table 22: A/A
Mux interface read AC characteristics
, for details of when the output becomes valid.
3.2.2
Bus Write
Bus Write operations write to the Command Interface. A valid Bus Write operation begins by
latching the Row Address and Column Address signals into the memory using the Address
Inputs, A0-A10, and the Row/Column Address Select RC. The data should be set up on the
Data Inputs/Outputs; Output Enable, G, and Interface Reset, RP, must be High, V
IH
and
Write Enable, W, must be Low, V
IL
. The Data Inputs/Outputs are latched on the rising edge
of Write Enable, W. See
Figure 14: A/A Mux interface Write AC waveforms
, and
Table 23:
A/A Mux interface Write AC characteristics
, for details of the timing requirements.
3.2.3
Output Disable
The data outputs are high-impedance when the Output Enable, G, is at V
IH
.
3.2.4
Reset
During Reset mode all internal circuits are switched off, the memory is deselected and the
outputs are put in high-impedance. The memory is in Reset mode when RP is Low, V
IL
. RP
must be held Low, V
IL
for t
PLPH
. If RP is goes Low, V
IL
, during a Program or Erase operation,
the operation is aborted and the memory cells affected no longer contain valid data; the
memory can take up to t
PLRH
to abort a Program or Erase operation.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW040NB5TG | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW040NB5TP | 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50LPW116 | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW116N1T | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW040NB5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW040NB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW080 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1 | 功能描述:閃存 3.6V 8M (1Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。