參數資料
型號: M41T256YMT
廠商: 意法半導體
英文描述: 256 Kbit 32K x8 SERIAL RTC
中文描述: 256千位32K的x8串行實時時鐘
文件頁數: 16/26頁
文件大?。?/td> 363K
代理商: M41T256YMT
M41T256Y
16/26
CLOCK OPERATION
Year, Month, and Date are contained in the last
three registers of the TIMEKEEPER
Register
Map (see Table 9). Bits D0 through D2 of the next
register contain the Day (day of week). Finally,
there are the registers containing the Seconds,
Minutes, and Hours, respectively. The first clock
register is the Control Register (this is described in
the Clock Calibration section).
The nine Clock Registers may be read one byte at
a time, or in a sequential block. The Control Reg-
ister (Address location 7FF8h) may be accessed
independently. Provision has been made to as-
sure that a clock update does not occur while any
of the nine clock addresses are being read. If a
clock address is being read, an update of the clock
registers will be halted. This will prevent a transi-
tion of data during the read.
Reading the Clock
The nine byte clock register (see Table 9) is used
to both set the clock and to read the date and time
from the clock, in a binary coded decimal format.
The system-to-user transfer of clock data will be
halted whenever the address being read is a clock
address (7FF9h to 7FFFh). The update will re-
sume either due to a Stop Condition or when the
pointer increments to a RAM address.
This prevents reading data in transition. The
TIMEKEEPER
cells in the Register Map are only
data registers and not actual clock counters, so
updating the registers can be halted without dis-
turbing the clock itself.
Setting the Clock
Bit D7 of the Control Register (7FF8h) is the Write
Clock Bit. Setting the Write Clock Bit to a '1' will al-
low the user to write the desired Day, Date, and
Time data in 24-hour BCD format. Resetting the
Write Clock Bit to a '0' then transfers the values of
all time registers (7FF8h-7FFFh) to the actual
clock counters and resets the internal divider (or
clock) chain.
Note:
The Tenths/Hundredths of Seconds Regis-
ter will automatically be reset to zero when the
WRITE Clock Bit is set.
Other register bits such as FT, TEB, and ST may
be written without setting the WC Bit. In such cas-
es, the clock data will be undisturbed and will re-
tain their previous values.
Stopping and Starting the Oscillator
The oscillator may be stopped at any time. If the
device is going to spend a significant amount of
time on the shelf, the oscillator can be turned off to
minimize current drain on the battery. The Stop Bit
(ST) is the most significant bit of the Seconds Reg-
ister. Setting it to '1' stops the oscillator. Setting it
to '0' restarts the oscillator in approximately one
second.
相關PDF資料
PDF描述
M41T256YMT7TR RCA-F TO RCA-F COUPLER
M41T256YMT7 RCA F TO BNC-M ADAPTER
M41T315W-65MH6E Serial Access Phantom RTC Supervisor
M41T315W-65MH6F Serial Access Phantom RTC Supervisor
M41T315W-65MH6TR Serial Access Phantom RTC Supervisor
相關代理商/技術參數
參數描述
M41T256YMT7 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7E 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7F 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC
M41T256YSH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC