參數資料
型號： M41T256YMT7E
廠商： 意法半導體
英文描述： 256 Kbit 32K x8 SERIAL RTC
中文描述： 256千位32K的x8串行實時時鐘
文件頁數： 13/27頁
文件大小： 185K
代理商： M41T256YMT7E
13/27
M41T256Y
CLOCK OPERATION
Year, Month, and Date are contained in the last
three registers of the TIMEKEEPER
Register
Map (see
Table 3., page 14
). Bits D0 through D2
of the next register contain the Day (day of week).
Finally, there are the registers containing the Sec-
onds, Minutes, and Hours, respectively. The first
clock register is the Control Register (this is de-
scribed in the Clock Calibration section).
The nine Clock Registers may be read one byte at
a time, or in a sequential block. The Control Reg-
ister (Address location 7FF8h) may be accessed
independently. Provision has been made to as-
sure that a clock update does not occur while any
of the nine clock addresses are being read. If a
clock address is being read, an update of the clock
registers will be halted. This will prevent a transi-
tion of data during the read.
Reading the Clock
The nine byte clock register (see
Table
3., page 14
) is used to both set the clock and to
read the date and time from the clock, in a binary
coded decimal format. The system-to-user trans-
fer of clock data will be halted whenever the ad-
dress being read is a clock address (7FF9h to
7FFFh). The update will resume either due to a
Stop Condition or when the pointer increments to
a RAM address.
This prevents reading data in transition. The
TIMEKEEPER
cells in the Register Map are only
data registers and not actual clock counters, so
updating the registers can be halted without dis-
turbing the clock itself.
Setting the Clock
Bit D7 of the Control Register (7FF8h) is the Write
Clock Bit. Setting the Write Clock Bit to a '1' will al-
low the user to write the desired Day, Date, and
Time data in 24-hour BCD format. Resetting the
Write Clock Bit to a '0' then transfers the values of
all time registers (7FF8h-7FFFh) to the actual
clock counters and resets the internal divider (or
clock) chain.
Note:
The Tenths/Hundredths of Seconds Regis-
ter will automatically be reset to zero when the
WRITE Clock Bit is set.
Other register bits such as FT, TEB, and ST may
be written without setting the WC Bit. In such cas-
es, the clock data will be undisturbed and will re-
tain their previous values.
Stopping and Starting the Oscillator
The oscillator may be stopped at any time. If the
device is going to spend a significant amount of
time on the shelf, the oscillator can be turned off to
minimize current drain on the battery. The Stop Bit
(ST) is the most significant bit of the Seconds Reg-
ister. Setting it to '1' stops the oscillator. Setting it
to '0' restarts the oscillator in approximately one
second.
相關PDF資料
PDF描述
M41T256YMT7F 256 Kbit 32K x8 SERIAL RTC
M41T315V Serial access phantom RTC supervisor
M41T315W Serial access phantom RTC supervisor
M41T56C64MY6E Serial Real Time Clock with 56 bytes of NVRAM+64 Kbit (8192 bit x 8) EEPROM
M41T56C64MY6F Serial Real Time Clock with 56 bytes of NVRAM+64 Kbit (8192 bit x 8) EEPROM
相關代理商/技術參數
參數描述
M41T256YMT7F 功能描述:實時時鐘 Serial 256K (32Kx8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T256YMT7TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC
M41T256YSH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit 32K x8 SERIAL RTC
M41T315V 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial access phantom RTC supervisor
M41T315V/W 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial Access Phantom RTC Supervisor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*