- 您現在的位置：買賣IC網 > PDF目錄98007 > M41T00SM6F (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | M41T00SM6F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, LEAD FREE, PLASTIC, SO-8 |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 225K |
| 代理商： | M41T00SM6F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
Operation
M41T00S
2.1.3
Stop data transfer
A change in the state of the data line, from low to high, while the clock is high, defines the
STOP condition.
2.1.4
Data valid
The state of the data line represents valid data when after a start condition, the data line is
stable for the duration of the high period of the clock signal. The data on the line may be
changed during the low period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a start condition and terminated with a stop condition.
The number of data bytes transferred between the start and stop conditions is not limited.
The information is transmitted byte-wide and each receiver acknowledges with a ninth bit.
By definition a device that gives out a message is called “transmitter,” the receiving device
that gets the message is called “receiver.” The device that controls the message is called
“master.” The devices that are controlled by the master are called “slaves.”
2.1.5
Acknowledge
Each byte of eight bits is followed by one acknowledge bit. this acknowledge bit is a low level
put on the bus by the receiver whereas the master generates an extra acknowledge related
clock pulse. A slave receiver which is addressed is obliged to generate an acknowledge
after the reception of each byte that has been clocked out of the slave transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock
pulse in such a way that the SDA line is a stable low during the high period of the
acknowledge related clock pulse. Of course, setup and hold times must be taken into
account. A master receiver must signal an end of data to the slave transmitter by not
generating an acknowledge on the last byte that has been clocked out of the slave. In this
case the transmitter must leave the data line high to enable the master to generate the
STOP condition.
Figure 4.
Serial bus data transfer sequence
AI00587
DATA
CLOCK
DATA LINE
STABLE
DATA VALID
START
CONDITION
CHANGE OF
DATA ALLOWED
STOP
CONDITION
相關PDF資料 |
PDF描述 |
|---|---|
| M41T00SMY6T | REAL TIME CLOCK, PDSO8 |
| M41T00 | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| M41T0DS6E | REAL TIME CLOCK, PDSO8 |
| M41T256YMH7TR | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M41T256YMT7F | REAL TIME CLOCK, PDSO44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T00SM6F-CUT TAPE | 制造商:ST 功能描述:M41TSM Series 2.7 to 5.5 V Serial I2C Real Time Clock Surface Mount - SOIC-8 |
| M41T01M6F | 制造商:STMicroelectronics 功能描述:REAL TIME CLOCKS 制造商:STMicroelectronics 功能描述:IC RTC SERIAL LP 8SOIC |
| M41T0DS6E | 功能描述:實時時鐘 Serial 64 (8x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T0DS6F | 功能描述:實時時鐘 Low Power Serial RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T0DS6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SERIAL REAL-TIME CLOCK |
發布緊急采購，3分鐘左右您將得到回復。