- 您現在的位置：買賣IC網 > PDF目錄98007 > M41T00SM6F (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | M41T00SM6F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, LEAD FREE, PLASTIC, SO-8 |
| 文件頁數： | 24/26頁 |
| 文件大小： | 225K |
| 代理商： | M41T00SM6F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁
M41T00S
Operation
2
Operation
The M41T00S clock operates as a slave device on the serial bus. Access is obtained by
implementing a start condition followed by the correct slave address (D0h). The 8 bytes
contained in the device can then be accessed sequentially in the following order:
1.
Seconds register
2.
Minutes register
3.
Century/hours register
4.
Day register
5.
Date register
6.
Month register
7.
Year register
8.
Calibration register
The M41T00S clock continually monitors VCC for an out-of-tolerance condition. Should VCC
fall below VPFD, the device terminates an access in progress and resets the device address
counter. Inputs to the device will not be recognized at this time to prevent erroneous data
from being written to the device from a an out-of-tolerance system. Once VCC falls below the
switchover voltage (VSO), the device automatically switches over to the battery and powers
down into an ultra-low current mode of operation to preserve battery life. If VBAT is less than
VPFD, the device power is switched from VCC to VBAT when VCC drops below VBAT. If VBAT is
greater than VPFD, the device power is switched from VCC to VBAT when VCC drops below
VPFD. Upon power-up, the device switches from battery to VCC at VSO. When VCC rises
above VPFD, it will recognize the inputs.
For more information on battery storage life refer to Application Note AN1012.
2.1
2-wire bus characteristics
The bus is intended for communication between different ICs. It consists of two lines: a
bidirectional data signal (SDA) and a clock signal (SCL). Both the SDA and SCL lines must
be connected to a positive supply voltage via a pull-up resistor.
The following protocol has been defined:
●
Data transfer may be initiated only when the bus is not busy.
●
During data transfer, the data line must remain stable whenever the clock line is high.
●
Changes in the data line, while the clock line is high, will be interpreted as control
signals.
Accordingly, the following bus conditions have been defined:
2.1.1
Bus not busy
Both data and clock lines remain high.
2.1.2
Start data transfer
A change in the state of the data line, from high to low, while the clock is high, defines the
START condition.
相關PDF資料 |
PDF描述 |
|---|---|
| M41T00SMY6T | REAL TIME CLOCK, PDSO8 |
| M41T00 | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| M41T0DS6E | REAL TIME CLOCK, PDSO8 |
| M41T256YMH7TR | 0 TIMER(S), REAL TIME CLOCK, PDSO44 |
| M41T256YMT7F | REAL TIME CLOCK, PDSO44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M41T00SM6F-CUT TAPE | 制造商:ST 功能描述:M41TSM Series 2.7 to 5.5 V Serial I2C Real Time Clock Surface Mount - SOIC-8 |
| M41T01M6F | 制造商:STMicroelectronics 功能描述:REAL TIME CLOCKS 制造商:STMicroelectronics 功能描述:IC RTC SERIAL LP 8SOIC |
| M41T0DS6E | 功能描述:實時時鐘 Serial 64 (8x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T0DS6F | 功能描述:實時時鐘 Low Power Serial RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| M41T0DS6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SERIAL REAL-TIME CLOCK |
發布緊急采購，3分鐘左右您將得到回復。