參數資料
型號： M41ST84W
廠商： 意法半導體
英文描述： 3.0/3.3V I2C Serial RTC with Supervisory Functions(帶監視功能的3.0/3.3V I2C串行RTC)
中文描述： 3.0/3.3V I2C串行實時時鐘具有監督職能（帶監視功能的3.0/3.3V的I2C串行時鐘）
文件頁數： 21/29頁
文件大?。?/td> 481K
代理商： M41ST84W
21/29
M41ST84W
Power-fail INPUT/OUTPUT
The Power-Fail Input (PFI) is compared to an in-
ternal reference voltage (1.25V). If PFI is less than
the power-fail threshold (V
PFI
), the Power-Fail
Output (PFO) will go low. This function is intended
for use as an under-voltage detector to signal a
failing power supply. Typically PFI is connected
through an external voltage divider (see
Figure
5., page 6
) to either the unregulated DC input (if it
is available) or the regulated output of the V
CC
reg-
ulator. The voltage divider can be set up such that
the voltage at PFI falls below V
PFI
several millisec-
onds before the regulated V
CC
input to the
M41ST84W or the microprocessor drops below
the minimum operating voltage.
During battery back-up, the power-fail comparator
turns off and PFO goes (or remains) low. This oc-
curs after V
CC
drops below V
PFD
(min). When pow-
er returns, PFO is forced high, irrespective of V
PFI
for the write protect time (t
rec
), which is the time
from V
PFD
(max) until the inputs are recognized. At
the end of this time, the power-fail comparator is
enabled and PFO follows PFI. If the comparator is
unused, PFI should be connected to V
SS
and PFO
left unconnected.
Century Bit
Bits D7 and D6 of Clock Register 03h contain the
CENTURY ENABLE Bit (CEB) and the CENTURY
Bit (CB). Setting CEB to a “1” will cause CB to tog-
gle, either from a “0” to “1” or from “1” to “0” at the
turn of the century (depending upon its initial
state). If CEB is set to a “0”, CB will not toggle.
Output Driver Pin
When the FT Bit, AFE Bit and watchdog register
are not set, the IRQ/FT/OUT pin becomes an out-
put driver that reflects the contents of D7 of the
Control Register. In other words, when D7 (OUT
Bit) and D6 (FT Bit) of address location 08h are a
'0,' then the IRQ/FT/OUT pin will be driven low.
Note:
The IRQ/FT/OUT pin is an open drain which
requires an external pull-up resistor.
Battery Low Warning
The M41ST84W automatically performs battery
voltage monitoring upon power-up and at factory-
programmed time intervals of approximately 24
hours. The Battery Low (BL) Bit, Bit D4 of Flags
Register 0Fh, will be asserted if the battery voltage
is found to be less than approximately 2.5V. The
BL Bit will remain asserted until completion of bat-
tery replacement and subsequent battery low
monitoring tests, either during the next power-up
sequence or the next scheduled 24-hour interval.
If a battery low is generated during a power-up se-
quence, this indicates that the battery is below ap-
proximately 2.5 volts and may not be able to
maintain data integrity in the SRAM. Data should
be considered suspect and verified as correct. A
fresh battery should be installed.
If a battery low indication is generated during the
24-hour interval check, this indicates that the bat-
tery is near end of life. However, data is not com-
promised due to the fact that a nominal V
CC
is
supplied. In order to insure data integrity during
subsequent periods of battery back-up mode, the
battery should be replaced. The battery may be re-
placed while V
CC
is applied to the device.
The M41ST84W only monitors the battery when a
nominal V
CC
is applied to the device. Thus appli-
cations which require extensive durations in the
battery back-up mode should be powered-up peri-
odically (at least once every few months) in order
for this technique to be beneficial. Additionally, if a
battery low is indicated, data integrity should be
verified upon power-up via a checksum or other
technique.
t
rec
Bit
Bit D7 of Clock Register 04h contains the t
rec
Bit
(TR). t
rec
refers to the automatic continuation of
the deselect time after V
CC
reaches V
PFD
. This al-
lows for a voltage setting time before WRITEs may
again be performed to the device after a power-
down condition. The t
rec
Bit will allow the user to
set the length of this deselect time as defined by
Table 7., page 22
.
Initial Power-on Defaults
Upon initial application of power to the device, the
following register bits are set to a '0' state: Watch-
dog Register, TR, FT, AFE, ABE, and SQWE. The
following bits are set to a '1' state: ST, OUT, and
HT (see
Table 8., page 22
).
相關PDF資料
PDF描述
M41ST84Y(中文) 512 bit (64 x 8) Serial RTC with Supervisory Functions
M41ST84 5.0 OR 3.0V, 512 bit (64 x 8) Serial RTC with supervisory functions(具有監控功能的5.0V或3.0V，512位(64 x 8)串行RTC)
M41ST85WMH6E 3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
M41ST85WMH6F 3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
M41ST85WMX6E 3.0/3.3V I2C Combination Serial RTC, NVRAM Supervisor and Microprocessor Supervisor
相關代理商/技術參數
參數描述
M41ST84W_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3.0/3.3 V I2C serial RTC with 44 bytes of NVRAM and supervisory functions
M41ST84WMH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
M41ST84WMH1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
M41ST84WMH1TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
M41ST84WMQ 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 or 3.0V, 512 bit 64 x 8 SERIAL RTC with SUPERVISORY FUNCTIONS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*