- 您現在的位置：買賣IC網 > PDF目錄67774 > M38K29RFS 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, CPGA100 PDF資料下載
參數資料
| 型號： | M38K29RFS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, CPGA100 |
| 封裝： | 0.65 MM PITCH, PGA-100 |
| 文件頁數： | 2/25頁 |
| 文件大?。?/td> | 1451K |
| 代理商： | M38K29RFS |
38K2 Group
Rev.3.00
Oct 15, 2006
page 8 of 147
REJ03B0193-0300
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5
flags which indicate the status of the processor after an arithmetic
operation and 3 flags which decide MCU operation. Branch opera-
tions can be performed by testing the Carry (C) flag , Zero (Z) flag,
Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z,
V, N flags are not valid.
Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
Bit 1: Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is “1”.
Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
Bit 4: Break flag (B)
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
Bit 5: Index X mode flag (T)
When the T flag is “0”, arithmetic operations are performed
between accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
Bit 7: Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
Table 4 Set and clear instructions of each bit of processor status register
Set instruction
Clear instruction
C flag
SEC
CLC
Z flag
–
I flag
SEI
CLI
D flag
SED
CLD
B flag
–
T flag
SET
CLT
V flag
–
CLV
N flag
–
相關PDF資料 |
PDF描述 |
|---|---|
| M41ST85YMH6 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41ST85YMX6TR | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41ST85YMH6F | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41ST85YMH6E | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41T11MH6 | 0 TIMER(S), REAL TIME CLOCK, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38K29T-ADF | 功能描述:DEV TEMPORARY TARGET BOARD FOR M RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M38K29T-PAC | 制造商:Renesas Electronics Corporation 功能描述:DEV SIMPLE TOOL SYSTEM PKG FOR 38000/38K - Bulk |
| M38UC-150 | 制造商:M/A-COM Technology Solutions 功能描述:MICROWAVE MIXER - Bulk |
| M3-90 | 制造商:Southco 功能描述: |
| M390003/01-2066 | 制造商:NA 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。