- 您現在的位置：買賣IC網 > PDF目錄370961 > M38C29MC-XXXHP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38C29MC-XXXHP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 27/63頁 |
| 文件大?。?/td> | 1000K |
| 代理商： | M38C29MC-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
27
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
(4) Set of Timer X Mode Register
Set the write control bit of the timer X mode register to
“
1
”
(write to
the latch only) when setting the IGBT output and PWM modes.
Output waveform simultaneously reflects the contents of both regis-
ters at the next underflow after writing to the timer X register (high-
order).
(5) Output Control Function of Timer X
When using the output control function (INT
1
and INT
2
) in the IGBT
output mode, set the levels of INT
1
and INT
2
to
“
H
”
in the falling edge
active or to
“
L
”
in the rising edge active before switching to the IGBT
output mode.
(6) Note on Switch of CNTR
0
Active Edge
When the CNTR
0
active edge switch bits are set, at the same time,
the interrupt active edge is also affected.
When the pulse width is measured, set the bit 7 of the CNTR
0
ac-
tive edge switch bits to
“
0
”
.
Timer Y
Timer Y is a 16-bit timer.
The timer Y count source can be selected by setting the timer Y mode
register. When f(X
CIN
) is selected as the count source, counting can
be performed regardless of X
CIN
oscillation. However, when X
CIN
is
stopped, the external pulse input from X
CIN
pin is counted.
Four operating modes can be selected for timer Y by the timer Y
mode register. Also, the real time port can be controlled.
(1) Timer Mode
The timer Y count source can be selected by setting the timer Y mode
register.
(2) Period Measurement Mode
The interrupt request is generated at rising/falling edge of CNTR
1
pin input signal. Simultaneously, the value in timer Y latch is reloaded
in timer Y and timer Y continues counting. Except for that, this mode
operates just as in the timer mode.
The timer value just before the reloading at rising/falling of CNTR
1
pin input is retained until the timer Y is read once after the reload.
The rising/falling timing of CNTR
1
pin input is found by CNTR
1
inter-
rupt. When using this mode, set the port sharing the CNTR
1
pin to
input mode.
(3) Event Counter Mode
The timer counts signals input through the CNTR
1
pin.
Except for that, this mode operates just as in the timer mode.
When using this mode, set the port sharing the CNTR
1
pin to input
mode.
(4) Pulse Width HL Continuously Measurement
Mode
The interrupt request is generated at both rising and falling edges of
CNTR
1
pin input signal. Except for that, this mode operates just as in
the period measurement mode. When using this mode, set the port
sharing the CNTR
1
pin to input mode.
I
Notes on Timer Y
G
CNTR
1
Interrupt Active Edge Selection
CNTR
1
interrupt active edge depends on the CNTR
1
active edge
switch bit. However, in pulse width HL continuously measurement
mode, CNTR
1
interrupt request is generated at both rising and falling
edges of CNTR
1
pin input signal regardless of the setting of CNTR
1
active edge switch bit.
G
Timer Y Read/Write Control
When reading from/writing to timer Y, read from/write to both the
high-order and low-order bytes of timer Y. When the value is read,
read the high-order bytes first and the low-order bytes next. When
the value is written, write the low-order bytes first and the high-
order bytes next.
If reading from the timer Y register during write operation or writing
to it during read operation is performed, normal operation will not
be performed.
When writing a value to the timer Y address to write to the latch
only, the value is set into the reload latch and the timer is updated
at the next underflow. Normally, when writing a value to the timer Y
address, the value is set into the timer and the timer latch at the
same time, because they are set to write at the same time.
When writing to the latch only, if the write timing to the high-order
reload latch and the underflow timing are almost the same, the value
is set into the timer and the timer latch at the same time. In this
time, counting is stopped during writing to the high-order reload
latch.
Do not switch the timer count source during timer count operation.
Stop the timer count before switching it.
G
Real Time Port Control
When the real time port function is valid, data for the real time port is
output from ports P4
7
and P4
6
each time the timer Y underflows.
(However, if the real time port control bit is changed from
“
0
”
to
“
1
”
after the data for real time port is set, data is output independent of
the timer Y operation.) When the data for the real time port is changed
while the real time port function is valid, the changed data is output at
the next underflow of timer Y. Before using this function, set the cor-
responding port direction registers to output mode.
相關PDF資料 |
PDF描述 |
|---|---|
| M38C2XMX | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M44C090 | Low-Current Microcontroller for Wireless Communication |
| M44C090-H | Low-Current Microcontroller for Wireless Communication |
| M44C890 | Low-Current Microcontroller for Wireless Communication |
| M44C890-H | Low-Current Microcontroller for Wireless Communication |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38C29RLFS | 功能描述:EMULATOR MCU FOR A-VERSION 38C2 RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| M38C29T-64FPD | 功能描述:DEV 100-PIN RFS/MCU TO 64-PIN 0. RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M38C29T-64LCA | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Converter from 100-pin RFS Type Emulator MCU to 64-pin 0.8mm-pitch QFP (for 38C1, 38C2, 38K0 and 38K2 Group of 38000 Series) |
| M38C29T-ADF | 功能描述:DEV TEMPORARY TARGET BOARD FOR M RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M38C2XMX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。