參數資料
型號： M38C29FFAHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64
封裝： 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數： 55/102頁
文件大?。?/td> 1567K
代理商： M38C29FFAHP
56
38C2 Group (A Version)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to
change.
Table 11 Summary of 38C2 group (A version)’s flash memory version
FLASH MEMORY MODE
The 38C2 group (A version)’s flash memory version has an inter-
nal new DINOR (DIvided bit line NOR) flash memory that can be
rewritten with a single power source when VCC is 4.5 to 5.5 V, and
2 power sources when VCC is 3.0 to 4.5 V.
For this flash memory, three flash memory modes are available in
which to read, program, and erase: the parallel I/O and standard
serial I/O modes in which the flash memory can be manipulated
using a programmer and the CPU rewrite mode in which the flash
memory can be manipulated by the Central Processing Unit
(CPU).
Summary
Table 11 lists the summary of the 38C2 group (A version)’s flash
memory version.
This flash memory version has some blocks on the flash memory
as shown in Figure 61 and each block can be erased.
In addition to the ordinary User ROM area to store the MCU op-
eration control program, the flash memory has a Boot ROM area
that is used to store a program to control rewriting in CPU rewrite
and standard serial I/O modes. This Boot ROM area has had a
standard serial I/O mode control program stored in it when
shipped from the factory. However, the user can write a rewrite
control program in this area that suits the user’s application sys-
tem. This Boot ROM area can be rewritten in only parallel I/O
mode.
Item
Power source voltage (Vcc)
Program/Erase VPP voltage (VPP)
Flash memory mode
Erase block division
User ROM area
Boot ROM area
Program method
Erase method
Program/Erase control method
Number of commands
Number of program/Erase times
ROM code protection
Specifications
VCC = 2.5 to 5.5 V (Note 1)
VCC = 2.5 to (VCC at program/erase) + 0.5 V (Note 2)
VPP = 4.5 to 5.5 V, VCC = 3.0 to 5.5 V
3 modes; Parallel I/O mode, Standard serial I/O mode, CPU rewrite mode
Refer to Fig. 61.
Not divided (4K bytes) (Note 3)
In units of bytes
Block erase
Program/Erase control by software command
5 commands
100 times
Available in parallel I/O mode and standard serial I/O mode
Notes 1: It is the rating value when Vcc = 5.0 to 5.5 V at program/erase.
2: It is the rating value when Vcc = 3.0 to 5.0 V at program/erase.
3: The Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory. This Boot ROM area can be
erased and written in only parallel I/O mode.
相關PDF資料
PDF描述
M38C24M4A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C24M6A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38C29FFAHP#U0 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 60KB FLASH 5V 64LQFP - Trays
M38C29FFFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29FFHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*