參數資料
型號： M38C29FFAHP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64
封裝： 10 X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數： 30/102頁
文件大小： 1567K
代理商： M38C29FFAHP
33
38C2 Group (A Version)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
[Transmit Buffer Register/Receive Buffer Reg-
ister (TB/RB)]
The transmit buffer register and the receive buffer register are lo-
cated at the same address. The transmit buffer is write-only and the
receive buffer is read-only. If a character bit length is 7 bits, the MSB
of data stored in the receive buffer is “0”.
[Serial I/O Status Register (SIO1STS, SIO2STS)]
The read-only serial I/O status register consists of seven flags (bits 0
to 6) which indicate the operating status of the serial I/O function and
various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is set to “0” when the receive buffer
register is read.
If there is an error, it is detected at the same time that data is trans-
ferred from the receive shift register to the receive buffer register,
and the receive buffer full flag is set. A write to the serial I/O status
register sets all the error flags OE, PE, FE, and SE (bit 3 to bit 6,
respectively) to “0”. Writing “0” to the serial I/O enable bit SIOE (bit 7
of the serial I/O control register) also sets all the status flags to “0”,
including the error flags.
All bits of the serial I/O status register are set to “0” at reset, but if the
transmit enable bit (bit 4) of the serial I/O control register has been
set to “1”, the transmit shift completion flag (bit 2) and the transmit
buffer empty flag (bit 0) become “1”.
[Serial I/O Control Register (SIO1CON, SIO2CON)]
The serial I/O control register consists of eight control bits for the
serial I/O function.
[UART Control Register (UART1CON, UART2CON)]
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set the
data format of an data transfer and one bit (bit 4) which is always
valid and sets the output structure of the P55/TXD1 [P32/TxD2] pin.
[Baud Rate Generator (BRG1, BRG2)]
The baud rate generator determines the baud rate for serial transfer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate generator.
相關PDF資料
PDF描述
M38C24M4A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C24M6A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
M38C29MCA-XXXHP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38C29FFAHP#U0 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 60KB FLASH 5V 64LQFP - Trays
M38C29FFFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29FFHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38C29MC-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*