- 您現在的位置：買賣IC網 > PDF目錄370954 > M38869MFA (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38869MFA |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 50/110頁 |
| 文件大?。?/td> | 1601K |
| 代理商： | M38869MFA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁
50
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
.
.
.
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 5.
LDA —
SEI
BBS 5, S1, BUSBUSY (BB flag confirming and branch pro-
cess)
BUSFREE:
STA S0
(Writing of slave address value)
LDM #$F0, S1
(Trigger of START condition generating)
CLI
(Interrupt enabled)
(Taking out of slave address value)
(Interrupt disabled)
BUSBUSY:
CLI
(Interrupt enabled)
2. Use “Branch on Bit Set” of “BBS 5, $0014, –” for the BB flag
confirming and branch process.
3. Use “STA $12, STX $12” or “STY $12” of the zero page ad-
dressing instruction for writing the slave address value to the
I
2
C data shift register.
4. Execute the branch instruction of above 2 and the store instruc-
tion of above 3 continuously shown the above procedure
example.
5. Disable interrupts during the following three process steps:
BB flag confirming
Writing of slave address value
Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
(3) RESTART condition generating procedure
This cannot be applied when the external memory is used and the
bus cycle is extended by ONW function.
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 4.)
Execute the following procedure when the PIN bit is “0.”
LDM #$00, S1
LDA —
SEI
STA S0
LDM #$F0, S1
CLI
(Select slave receive mode)
(Taking out of slave address value)
(Interrupt disabled)
(Writing of slave address value)
(
Trigger of RESTART condition generating
)
(Interrupt enabled)
2. Select the slave receive mode when the PIN bit is “0.” Do not
write “1” to the PIN bit. Neither “0” nor “1” is specified for the
writing to the BB bit.
The TRX bit becomes “0” and the S
DA
pin is released.
3. The S
CL
pin is released by writing the slave address value to
the I
2
C data shift register.
4. Disable interrupts during the following two process steps:
Writing of slave address value
Trigger of RESTART condition generating
(4) Writing to I
2
C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and
an instruction to set the MST and TRX bits to “0” from “1” simulta-
neously. It is because it may enter the state that the S
CL
pin is
released and the S
DA
pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to “0” from “1” simultaneously when the PIN bit is “1.” It is because
it may become the same as above.
(5) Process of after STOP condition generating
Do not write data in the I
2
C data shift register S0 and the I
2
C sta-
tus register S1 until the bus busy flag BB becomes “0” after
generating the STOP condition in the master mode. It is because
the STOP condition waveform might not be normally generated.
Reading to the above registers do not have the problem.
(6) STOP condition input at 7th clock pulse
In the slave mode, the STOP condition is input at the 7th clock
pulse while receiving a slave address or data. As the clock pulse
is continuously input, the SDA line may be held at LOW even if
flag BB is set to “0” (only for M38867M8A and M38867E8).
Countermeasure:
Write dummy data to the I
2
C shift register or reset the ES0 bit in
the S1D register (ES0 = “L”
→
ES0 = “H”) during a stop condition
interrupt routine with flag PIN = “1”.
Note:
Do not use the read-modify-write instruction at this time.
Furthermore, when the ES0 bit is set to “0”, it becomes a
general-purpose port; so that the port must be set to input
mode or “H”.
(7) ES0 bit switch
In standard clock mode when SSC = “00010
2
” or in high-speed
clock mode, flag BB may switch to “1” if ES0 bit is set to “1” when
SDA is “L”.
Countermeasure:
Set ES0 to “1” when SDA is “H”.
相關PDF資料 |
PDF描述 |
|---|---|
| M38869MFA-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MFA-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3886 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M38867M8A-A01HP | BUTT SPLICE INSULKRIMP TAPED (B-231XT) |
| M38867M8A-A04HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38869MFA-XXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MFA-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MF-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38881E2FS | 功能描述:EMULATOR CHIP EPROM MCU/8BIT RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| M38902 SL001 | 制造商:Alpha Wire Company 功能描述:CBL 2COND 24AWG SLT 1000' |
發布緊急采購，3分鐘左右您將得到回復。