- 您現在的位置：買賣IC網 > PDF目錄370955 > M38869M8A-012HP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38869M8A-012HP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 81/110頁 |
| 文件大小： | 1601K |
| 代理商： | M38869M8A-012HP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁
81
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
(3) Flash memory mode 3 (CPU reprogramming
mode)
The M38869FFAHP/GP has the CPU reprogramming mode where
a built-in flash memory is handled by the central processing unit
(CPU).
In CPU reprogramming mode, the flash memory is handled by
writing and reading to/from the flash memory control register (see
Figure 79) and the flash command register (see Figure 80).
The CNV
SS
pin is used as the V
PP
power supply pin in CPU repro-
gramming mode. It is necessary to apply the power-supply voltage
of V
PP
H from the external to this pin.
Functional Outline (CPU reprogramming mode)
Figure 79 shows the flash memory control register bit configura-
tion. Figure 80 shows the flash command register bit
configuration.
Bit 0 of the flash memory control register is the CPU reprogram-
ming mode select bit. When this bit is set to “1” and V
PP
H is
applied to the CNVss/V
PP
pin, the CPU reprogramming mode is
selected. Whether the CPU reprogramming mode is realized or
not is judged by reading the CPU reprogramming mode monitor
flag (bit 2 of the flash memory control register).
Bit 1 is a busy flag which becomes “1” during erase and program
execution.
Whether these operations have been completed or not is judged
by checking this flag after each command of erase and the pro-
gram is executed.
Bits 4, 5 of the flash memory control register are the erase/pro-
gram area select bits. These bits specify an area where erase and
program is operated. When the erase command is executed after
an area is specified by these bits, only the specified area is
erased. Only for the specified area, programming is enabled; for
the other areas, programming is disabled.
When CPU reprogramming mode is valid, the area where is not
specified by the erase/program area select bits cannot be read
out.
Transfer CPU reprogramming mode control program to internal
RAM before entering the CPU reprogramming mode, and then ex-
ecute this program on internal RAM.
If an interrupt occurs while this program is being executed, the
flash memory area is accessed, but normally operation cannot be
performed because the flash memory area cannot be read out.
During CPU reprogramming mode control program execution, ex-
ecute the processing such as interrupt disabled, etc.
Figure 81 shows the CPU mode register bit configuration in the
CPU reprogramming mode. Set bits 1 and 0 to “00” (single-chip
mode) in the CPU reprogramming mode.
Fig. 79 Flash memory control register bit configuration
7
6
5
4
3
2
1
0
0
0
Flash memory control regsiter
(FCON : address 0FFE
16
)
CPU reprogramming mode select bit
(Note)
0 : CPU reprogramming mode is invalid. (Normal operation mode)
1 : When applying 0 V or V
PP
L to CNV
SS
/V
PP
pin, CPU reprogramming mode is
invalid. When applying V
PP
H to CNV
SS
/V
PP
pin, CPU reprogramming mode is valid.
Erase/Program busy flag
0 : Erase and program are completed or not have been executed.
1 : Erase/program is being executed.
CPU reprogramming mode monitor flag
0 : CPU reprogramming mode is invalid.
1 : CPU reprogramming mode is valid.
Erase/Program area select bits
0 0 : Addresses 1000
16
to FFFF
16
(total 60 Kbytes)
0 1 : Addresses 1000
16
to 7FFF
16
(total 28 Kbytes)
1 0 : Addresses 8000
16
to FFFF
16
(total 32 Kbytes)
1 1 : Not available
Fix this bit to “0.”
Fix this bit to “0.”
Note:
Bit 0 can be reprogrammed only when 0 V is applied to the CNV
SS
/V
PP
pin.
Not used (returns "0" when read)
相關PDF資料 |
PDF描述 |
|---|---|
| M38B40EDH-XXXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B4XMXH | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B43EDH-XXXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38B43M2H-XXXXFP | OSC 3.3V SMT 7X5 CMOS |
| M38B43M3H-XXXXFP | OSC 3.3V SMT 7X5 CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38869M8A-XXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869M8A-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869M8-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869M9-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38869MA-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。