參數資料
型號： M38867M8A-A07HP
廠商： Mitsubishi Electric Corporation
英文描述： connectors
中文描述： 單芯片8位CMOS微機
文件頁數： 78/110頁
文件大?。?/td> 1601K
代理商： M38867M8A-A07HP
78
3886 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
G
Erase command
Input command code 20
16
in the first transfer and command code
20
16
again in the second transfer. When this is done, the
M38869FFAHP/GP executes an erase command. Erase is initi-
ated at the last rising edge of the serial clock. The BUSY pin is
driven high during the erase operation. Erase is completed within
9.5 ms as measured by the internal timer, and the BUSY pin is
pulled low. Note that data 00
16
must be written to all memory loca-
tions before executing the erase command.
Note:
A erase operation is not completed by executing the erase
command once. Always be sure to execute a erase verify
command after executing the erase command. When the fail-
ure is found in the verification, the user must repeatedly ex-
ecute the erase command until the pass in the verification.
Refer to Figure 71 for the erase flowchart.
Fig. 76 Timings at erasing
G
Erase verify command
The user must verify the contents of all addresses after complet-
ing the erase command. Input command code A0
16
in the first
transfer. Proceed and input the low-order 8 bits and the high-order
8 bits of the address and pull the OE pin low. When this is done,
the M38869FFAHP/GP reads out the contents of the specified ad-
dress, and then latchs it into the internal data latch. When the OE
pin is released back high and serial clock is input to the SCLK pin,
the verify data that has been latched into the data latch is serially
output from the SDA pin.
Note:
If any memory location where the contents have not been
erased is found in the erase verify operation, execute the op-
eration of “erase
→
erase verify” over again. In this case,
however, the user does not need to write data 00
16
to memory
locations before erasing.
Fig. 77 Timings during erase verify
tw
E
SCLK
BUSY
OE
SDA
t
CH
t
EC
0 0 0 0 0 1 0 0
Command code input (20
16
) Command code input (20
16
)
0 0 0 0 0 1 0 0
Erase
“H”
“L”
SCLK
BUSY
OE
SDA
t
CH
A
0
A
7
A
8
A
15
D
0
D
7
t
CH
t
CREV
Command code input (A0
16
) Verify address input (L)
Verify address input (H)
Verify data output
t
WR
Verify read
t
RC
Note :
When outputting the verify data, the SDA pin is switched for output at the first falling edge of SCLK. The SDA pin is placed
in the floating state during the period of th
(C-E)
after the last rising edge of SCLK (at the 8th bit).
0 0 0 0 0 1 0 1
相關PDF資料
PDF描述
M38867M8A-A11HP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38869FFAHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38869M8A-XXXGP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38869M8A-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38869M8A-012HP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38867M8A-A11HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867M8A-XXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867M8-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867M9-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867MA-XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*