- 您現在的位置：買賣IC網 > PDF目錄370954 > M38512M4 (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38512M4 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 25/61頁 |
| 文件大?。?/td> | 904K |
| 代理商： | M38512M4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
25
3851 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 25 Interrupt request signal generating timing
Fig. 24 Structure of I
2
C status register
Bit 6: Communication mode specification bit (transfer direc-
tion specification bit: TRX)
This bit decides a direction of transfer for data communication.
When this bit is “0,” the reception mode is selected and the data of
a transmitting device is received. When the bit is “1,” the transmis-
sion mode is selected and address data and control data are
output onto the SDA in synchronization with the clock generated
on the S
CL
.
This bit is set/reset by software and hardware. About set/reset by
hardware is described below. This bit is set to “1” by hardware
when all the following conditions are satisfied:
When ALS is “0”
In the slave reception mode or the slave transmission mode
When the R/W bit reception is “1”
This bit is set to “0” in one of the following conditions:
When arbitration lost is detected.
When a STOP condition is detected.
When writing “1” to this bit by software is invalid by the START
condition duplication preventing function
(Note)
.
With MST = “0” and when a START condition is detected.
With MST = “0” and when ACK non-return is detected.
At reset
Bit 7: Communication mode specification bit (master/slave
specification bit: MST)
This bit is used for master/slave specification for data communica-
tion. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are re-
ceived, and data communication is performed in synchronization
with the clock generated by the master. When this bit is “1,” the
master is specified and a START condition and a STOP condition
are generated. Additionally, the clocks required for data communi-
cation are generated on the SCL.
This bit is set to “0” in one of the following conditions.
Immediately after completion of 1-byte data transfer when arbi-
tration lost is detected
When a STOP condition is detected.
Writing “1” to this bit by software is invalid by the START condi-
tion duplication preventing function
(Note)
.
At reset
Note:
START condition duplication preventing function
The MST, TRX, and BB bits is set to “1” at the same time after con-
firming that the BB flag is “0” in the procedure of a START condition
occurrence. However, when a START condition by another master
device occurs and the BB flag is set to “1” immediately after the con-
tents of the BB flag is confirmed, the START condition duplication
preventing function makes the writing to the MST and TRX bits in-
valid. The duplication preventing function becomes valid from the
rising of the BB flag to reception completion of slave address.
S
CL
PIN
IICIRQ
b7
MST
b0
I
2
C status register
(S1 : address 002D
16
)
Last receive bit
(Note)
0 : Last bit = “0”
1 : Last bit = “1”
General call detecting flag
(Note)
0 : No general call detected
1 : General call detected
Slave address comparison flag
(Note)
0 : Address disagreement
1 : Address agreement
Arbitration lost detecting flag
(Note)
0 : Not detected
1 : Detected
SCL pin low hold bit
0 : SCL pin low hold
1 : SCL pin low release
Bus busy flag
0 : Bus free
1 : Bus busy
Communication mode
specification bits
00 : Slave receive mode
01 : Slave transmit mode
10 : Master receive mode
11 : Master transmit mode
TRX BB PIN
AL AAS AD0 LRB
Note:
These bits and flags can be read out, but cannot
be written.
Write “0” to these bits at writing.
相關PDF資料 |
PDF描述 |
|---|---|
| M388504E6SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M388504E6SS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3850 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M388504E6FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38867E8A-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38513E4FP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube |
| M38513E4FP#U0 | 功能描述:IC 740 MCU ROM 16K 42SSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38514E6FP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube |
| M38514E6SP | 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube |
| M38517T-ADS | 功能描述:DEV TMP TRGT BRD FOR M38517RSS & RoHS:否 類別:編程器，開發(fā)系統(tǒng) >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
發(fā)布緊急采購，3分鐘左右您將得到回復。