參數資料
型號: M38039MCH-XXXKP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
封裝: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64
文件頁數: 89/119頁
文件大?。?/td> 1818K
代理商: M38039MCH-XXXKP
Rev.3.11
Apr 5, 2006
Page 69 of 113
REJ03B0017-0311
3803 Group (Spec.H)
Boot Mode
The control program for CPU rewrite mode must be written into
the User ROM or Boot ROM area in parallel I/O mode
beforehand. (If the control program is written into the Boot ROM
area, the standard serial I/O mode becomes unusable.)
See Figure.64 for details about the Boot ROM area.
Normal microcompu ter mo de is e n t e red when the
microcomputer is reset with pulling CNVSS pin low. In this case,
the CPU starts operating using the control program in the User
ROM area.
When the microcomputer is reset and the CNVSS pin high after
pulling the P45/TxD1 pin and CNVSS pin high, the CPU starts
operating (start address of program is stored into addresses
FFFC16 and FFFD16) using the control program in the Boot
ROM area. This mode is called the “Boot mode”. Also, User
ROM area can be rewritten using the control program in the Boot
ROM area.
Block Address
Block addresses refer to the maximum address of each block.
These addresses are used in the block erase command.
CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated
on (read, program, or erase) under control of the Central
Processing Unit (CPU).
In CPU rewrite mode, only the User ROM area shown in
Figure.64 can be rewritten; the Boot ROM area cannot be
rewritten. Make sure the program and block erase commands are
issued for only the User ROM area and each block area.
The control program for CPU rewrite mode can be stored in
either User ROM or Boot ROM area. In the CPU rewrite mode,
because the flash memory cannot be read from the CPU, the
rewrite control program must be transferred to internal RAM
area before it can be executed.
Fig 64. Block diagram of built-in flash memory
Data block A:
2K bytes
Block 3: 24K bytes
Block 2: 16K bytes
Block 1: 8 K bytes
Block 0: 8 K bytes
FFFF16
E00016
C00016
800016
200016
180016
100016
User ROM area
Data block B:
2K bytes
SFR area
Internal RAM area
(2K bytes)
FFFF16
100016
0FFF16
0FE016
083F16
004016
000016
FFFF16
F00016
Boot ROM area
4K bytes
SFR area
Internal flash memory area
(60K bytes)
RAM
Notes1
: The boot ROM area can be rewritten
in a parallel I/O mode. (Access to
except boot ROM area is disabled.)
2
: To specify a block, use the maximum
address in the block.
相關PDF資料
PDF描述
M38039FFHHP 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
M38037M8H-XXXHP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
M38037M6H-XXXFP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
M38039FFHFP 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
M38039MFH-XXXFP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38049FFFP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049FFLHP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049RLSS 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器,開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3806 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3806 BK001 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000'