參數資料
型號： M38039GCH-XXXKP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64
文件頁數： 85/103頁
文件大?。?/td> 1412K
代理商： M38039GCH-XXXKP
REJ03B0166-0113 Rev.1.13
Aug 21, 2009
Page 82 of 100
3803 Group (Spec.H QzROM version)
Notes on Interrupts
1. Change of relevant register settings
When the setting of the following registers or bits is changed, the
interrupt request bit may be set to “1”. When not requiring the
interrupt occurrence synchronized with these setting, take the
following sequence.
Interrupt edge selection register (address 003A16)
Timer XY mode register (address 002316)
Timer Z mode register (address 002A16)
Set the above listed registers or bits as the following sequence.
Fig 80. Sequence of changing relevant register
<Reason>
2. Check of interrupt request bit
When executing the BBC or BBS instruction to an interrupt
request bit of an interrupt request register immediately after this
bit is set to “0”, execute one or more instructions before
executing the BBC or BBS instruction.
Fig 81. Sequence of check of interrupt request bit
<Reason>
If the BBC or BBS instruction is executed immediately after an
interrupt request bit of an interrupt request register is cleared to
“0”, the value of the interrupt request bit before being cleared to
“0” is read.
Notes on 8-bit Timer (timer 1, 2, X, Y)
If a value n (between 0 and 255) is written to a timer latch, the
frequency division ratio is 1/(n+1).
When switching the count source by the timer 12, X and Y
count source selection bits, the value of timer count is altered
in unconsiderable amount owing to generating of thin pulses in
the count input signals.
Therefore, select the timer count source before set the value to
the prescaler and the timer.
Set the double-function port of the CNTR0/CNTR1 pin and
port P54/P55 to output in the pulse output mode.
Set the double-function port of CNTR0/CNTR1 pin and port
P54/P55 to input in the event counter mode and the pulse width
measurement mode.
Set the interrupt edge select bit (active edge switch bit)
or the interrupt (source) select bit to “1”.
NOP (one or more instructions)
Set the corresponding interrupt enable bit to “0” (disabled).
Set the corresponding interrupt request bit to “0”
(no interrupt request issued).
Set the corresponding interrupt enable bit to “1” (enabled).
NOP (one or more instructions)
Clear the interrupt request bit to “0” (no interrupt issued)
Execute the BBC or BBS instruction
相關PDF資料
PDF描述
M38039GCH-XXXWG 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PBGA64
M38039G8HKP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64
M38049FFHHP 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
M38049FFHSP 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PDIP64
M38049FFHFP 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38049FFFP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049FFLHP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049RLSS 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3806 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3806 BK001 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*