- 您現在的位置：買賣IC網 > PDF目錄45037 > M37905F8CFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M37905F8CFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64 |
| 文件頁數： | 14/29頁 |
| 文件大小： | 284K |
| 代理商： | M37905F8CFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
16-BIT CMOS MICROCOMPUTER
M37905F8CFP, M37905F8CSP
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
21
Fig. 9 Programming flowchart
Fig. 10 Block erase flowchart
Start
Write 4016
Write,
Address, Data
Flash memory control
register Read
Full status check
Programming
Completed
NO
YES
RY/BY Status
Bit = 1?
Write 2016
Write D016,
Flash memory control
register Read
Full status check
Block erase Completed
NO
YES
Block address
Start
RY/BY Status
Bit = 1?
Erase All Block Command (2016/2016)
Writing command code “2016” at the 1st bus cycle and writing com-
mand code “2016” at the subsequent 2nd bus cycle initiate the con-
tinuous block erase (chip erase) operations for all the blocks.
The completion of the chip erase operation, as well as of the block
erase operation, is confirmed by a read of the flash memory control
register. The result of the automatic erase operation is also reported
by a read of the status register.
During the automatic erase operation (when the RY/BY status bit =
“0”), writing of commands and access to the flash memory must not
be performed.
Status Register
The status register is used to indicate whether the programming/
erase operation has been completed normally or terminated by an
error. By writing the read status register command (7016), the con-
tents of the status register can be read out; by writing the clear sta-
tus register command (5016), the contents of the status register can
be cleared.
Table 3 lists the definition of each bit of the status register.
The status register outputs “8016” after reset is removed.
The status of each bit is described below.
相關PDF資料 |
PDF描述 |
|---|---|
| M37905F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP64 |
| M37905M4C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| M37905M4C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| M37905M8C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| M37905M8C-XXXSP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37905F8CSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905M4C | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M4C-XXXSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37905M6C-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。