參數資料
型號： M37753S4CFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80
封裝： PLASTIC, QFP-80
文件頁數： 55/110頁
文件大?。?/td> 1439K
代理商： M37753S4CFP
MITSUBISHI MICROCOMPUTERS
M37753M8C-XXXFP, M37753M8C-XXXHP
M37753S4CFP, M37753S4CHP
48
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Transmission
Transmission is started when bit 0 (TEj flag) of UARTj Transmit/Re-
ceive control register 1 is “1”, bit 1 (TIj flag) of one is “0”, and CTSj
input is “L”. As shown in Figure 60, data is output from TXDj pin each
time when transmission clock CLKj changes from “H” to “L”. The data
is output from the least significant bit.
The TIj flag indicates whether the transmit buffer register is empty or
not. It is cleared to “0” when data is written in the transmit buffer reg-
ister and set to “1” when the contents of the transmit buffer register is
transferred to the transmit register.
When the transmit register becomes empty after the contents has
been transmitted, data is transferred automatically from the transmit
buffer register to the transmit register if the next transmission start
condition is satisfied. If bit 2 of UARTj Transmit/Receive control reg-
ister 0 is “1”, CTSj input is ignored, and transmission start is con-
trolled only by the TEj flag and TIj flag. Once transmission has
started, the TEj flag, TIj flag, and CTSj signals are ignored until data
transmission completes. Therefore, transmission is not interrupt
when CTSj input is changed to “H” during transmission.
The transmission start condition indicated by TEj flag, TIj flag, and
CTSj is checked while the TENDj signal (shown in Figure 60) is “H”.
Therefore, data can be transmitted continuously if the next transmis-
sion data is written in the transmit buffer register and TIj flag is
cleared to “0” before theTENDj signal goes “H”.
Bit 3 (TXEPTYj flag) of UARTj Transmit/Receive control register 0
changes to “1” at the next cycle just after the TENDj signal goes “H”
and changes to “0” when transmission starts. Therefore, this flag can
be used to determine whether data transmission has completed.
When the TIj flag changes from “0” to “1”, the interrupt request bit in
the UARTj transmit interrupt control register is set to “1”.
In only UART0, data can be output to a maximum of 3 external re-
ceive devices. This is realized under the condition in which the inter-
nal clock is selected and the transmission clock is output from one of
pins CLK0, CLKS0 (multiplexed with RXD0) and CLKS1 (multiplexed
with CTS0/RTS0). Make sure that do not switch the selection of the
clock during transmission. Figure 61 shows an external connection
example.
Plural output of transmit clock mode is set with bits 1 and 0 of the
particular function select register 1. Additionally, it is necessary to se-
lect the internal clock, disable CTS and RTS, receive and D-A output
with the UART0 Transmit/Receive mode register, UART0 Transmit/
Receive control registers 0 and 1, and A-D control register 1. Figure
62 shows the relevant registers bit configuration in plural output of
transmit clock mode and Figure 63 shows the particular function se-
lect register 1 bit configuration .
Table 6 shows the function of the particular function select register
1’s bits 1 and 0, which is the output pin of transmit clock select bits:
TC1 and TC0. According to this table, select the CLK0, CLKS0 or
CLKS1 pin corresponding to the contents of TC1 and TC0, and out-
put the transmit clock.
Fig. 60 Clock synchronous serial I/O timing
Transmission
clock
TEj
1/Pfi
× (n + 1) × 2
1/Pfi
× (n + 1) × 2
TIj
CTSj
Write in transmit buffer register
D0 D1 D2 D3 D4 D5 D6 D7
D1 D2 D3 D4 D5 D6 D7
D0 D1 D2 D3 D4 D5 D6 D7
D0
Transmit register
←Transmit buffer register
Stopped because TEj = “0”
CLKj
TENDj
TXDj
TXEPTYj
相關PDF資料
PDF描述
M37753S4CFP 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80
M37753M8C-XXXHP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80
M37754M6C-XXXGP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100
M37795STJ 16-BIT, 8 MHz, MICROCONTROLLER, PQCC84
M37795SJ 16-BIT, 8 MHz, MICROCONTROLLER, PQCC84
相關代理商/技術參數
參數描述
M37753S4CHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37754 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER
M37754FFCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37754FFCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37754M6C-XXXGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*