- 您現在的位置：買賣IC網 > PDF目錄69014 > M37753FFCFP 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37753FFCFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP-80 |
| 文件頁數： | 29/67頁 |
| 文件大小： | 0K |
| 代理商： | M37753FFCFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
35
MITSUBISHI MICROCOMPUTERS
M37753FFCFP
M37753FFCHP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
SHINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
Auto erase command
When writing “3016” twice continuously to the flash command regis-
ter, the flash memory control circuit executes the auto erase se-
quence described below for the area specified beforehand by the
erase/program area select bits.
(1) Data “0016" is written to the area to be erased in the flash
memory.
(2) The erasure is executed.
(3) The contents of the erased flash memory is erase-verified one by
one. When the address which is not erased is found, verification
is interrupted, and after the erase command is executed again,
erase-verification is operated again.
(4) When the erasure of all areas specified to be erased, is con-
firmed by erase-verify-operation, the auto erase command is
ended.
The auto erase/erase/program busy flag of the flash memory control
register becomes “1" when auto erase starts, and becomes “0" when
auto erase completes. Accordingly, CPU can recognize the comple-
tion of auto erase by polling this bit.
During auto erase, watchdog timer stops with “FF16” set.
Note: When the flash memory is erased by using the auto erase
command, it is unnecessary to execute the erase and erase
verify commands. Figure 25 shows the flowchart when auto
erase is executed.
DC electric characteristics
Note: The characteristic of the flash memory part are the same as
the standard of the parallel I/O mode.
AC electric characteristics
Note: The characteristics are the same as the standards of the mi-
crocomputer mode.
Reset command
The reset command is a command to discontinue the program,
erase, or the auto erase command on the way. When “FF16” is writ-
ten to the command register two times continuously after “4016,”
“2016,” or “3016” is written to the flash command register, the pro-
gram, erase, or auto erase command becomes invalid (reset), and
the M37753FFCFP and the M37753FFCHP enters the reset mode.
The contents of the memory does not change even if the reset com-
mand is executed.
Fig. 25 Flowchart when program/erase/auto erase is executed (2)
START
WRITE AUTO-ERASE
COMMAND
NOP ! 10
3016
DEVICE
PASSED
Auto erase
YES
ERASE PROGRAM
BUSY FLAG = 0
WRITE AUTO-ERASE
COMMAND
3016
NO
相關PDF資料 |
PDF描述 |
|---|---|
| M37753M8C-XXXHP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753S4CHP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753M8C-XXXFP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753S4CFP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753S4CFP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37753FFCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 16 BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37753M6C-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753M6C-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753M8C-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753M8C-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。