- 您現在的位置：買賣IC網 > PDF目錄370848 > M37735S4LHP (Mitsubishi Electric Corporation) 16-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37735S4LHP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | 16-BIT CMOS MICROCOMPUTER |
| 中文描述： | 16位CMOS微機 |
| 文件頁數： | 14/36頁 |
| 文件大小： | 935K |
| 代理商： | M37735S4LHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MITSUBISHI MICROCOMPUTERS
M37735S4BFP
16-BIT CMOS MICROCOMPUTER
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
As shown in Table 3,
output disable selection bit = “1”. In this case, write “1” to the port P4
2
direction register.
Table 1 shows the relationship between the CNVss pin input level
and the processor mode.
1
output can be stopped with the signal
Table 1. Relationship between CNVss pin input levels and processor
mode
CNVss
Mode
Microprocessor
Vcc
Description
Microprocessor mode upon
starting after reset.
00 0880
16
to
00 7FFF
16
00 8000
16
to
03 FFFF
16
04 0000
16
to
07 FFFF
16
08 0000
16
to
0B FFFF
16
0C 0000
16
to
0F FFFF
16
Table 2. Relationship between access addresses and chip-select signals
CS
0
to
CS
4
Access address
Microprocessor mode
Chip-select
signal
Area
The latter half of bank 00
16
except
internal memory area and banks
01
16
to 03
16.
Banks 04
16
to 07
16
Banks 08
16
to 0B
16
Banks 0C
16
to 0F
16
The first half of bank 00
16
except
internal memory area
____
0
____
1
____
CS
2
____
3
____
CS
4
Table 3. Function of signal output disable selection bit CM
6
(bit 6 of oscillation circuit control register 0)
Function
CM
6
= “0”
CM
6
= “1”
Processor mode
Pin
Note.
Functions shown in Table 3 cannot be emulated with a debugger. For the oscillation circuit control register 0 and port function control
register, refer to Figures 64 and 11 in data sheet “M37735MHBXXXFP”, respectively.
___ ___ ___
RDE
WEL
WEH
are output when the
internal/external memory area is accessed.
After WIT/STP instruction is executed,
“H” is output.
Clock
output selection bit.
1
is output independent of
1
___ ___ ___
are output only when the
external memory area is accessed.
“L” is output after WIT/STP instruction is
executed
Standby state selection bit (bit 0 of port
function control register) must be set to “1”.
“H” or “L” is output. (Contents of P4
2
port
latch is output.)
Port P4
2
direction register must be set to
“1”.
___
,
___
WEL
,
WEH
___
1
Microprocessor mode
14
相關PDF資料 |
PDF描述 |
|---|---|
| M37736M4B | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736M4BXXXGP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736M4L | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736M4LXXXHP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736MHB | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37735T-PAC | 制造商:Renesas Electronics Corporation 功能描述:DEV 7733 SIMPLE DEVELOPMENT TOOL PACKAGE - Bulk |
| M37736EHB | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736EHBXXXGP |
| M37736EHBGS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:PROM VERSION OF M37736MHBXXXGP |
| M37736EHBXXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHBXXXGP(MICROCOMPUTERS) |
| M37736EHL | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHLXXXHP(MICROCOMPUTERS) |
發布緊急采購，3分鐘左右您將得到回復。