- 您現在的位置：買賣IC網 > PDF目錄370847 > M37702S1AFP (Mitsubishi Electric Corporation) Single Chip 16 Bits CMOS Microcomputer(16位單片機) PDF資料下載
參數資料
| 型號： | M37702S1AFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| 中文描述： | 單片微機16位的CMOS（16位單片機） |
| 文件頁數： | 8/59頁 |
| 文件大?。?/td> | 811K |
| 代理商： | M37702S1AFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
8
MITSUBISHI MICROCOMPUTERS
M37702M2AXXXFP, M37702M2BXXXFP
M37702S1AFP, M37702S1BFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
STACK POINTER (S)
Stack pointer (S) is a 16-bit register. It is used during a subroutine
call or interrupts. It is also used during stack, stack pointer rela-
tive, or stack pointer relative indirect indexed Y addressing mode.
PROGRAM COUNTER (PC)
Program counter (PC) is a 16-bit counter that indicates the low-or-
der 16-bits of the next program memory address to be executed.
There is a bus interface unit between the program memory and
the CPU, so that the program memory is accessed through bus in-
terface unit. This is described later.
PROGRAM BANK REGISTER (PG)
Program bank register is an 8-bit register that indicates the high-
order 8 bits of the next program memory address to be executed.
When a carry occurs by incrementing the contents of the program
counter, the contents of the program bank register (PG) is
incremented by 1. Also, when a carry or borrow occurs after add-
ing or subtracting the offset value to or from the contents of the
program counter (PC) using branch instruction, the contents of the
program bank register (PG) is incremented or decremented by 1
so that programs can be written without worrying about bank
boundaries.
DATA BANK REGISTER (DT)
Data bank register (DT) is an 8-bit register. With some addressing
modes, a part of the data bank register (DT) is used to specify a
memory address. The contents of data bank register (DT) is used
as the high-order 8 bits of a 24-bit address. Addressing modes
that use the data bank register (DT) are direct indirect, direct in-
dexed X indirect, direct indirect indexed Y, absolute, absolute bit,
absolute indexed X, absolute indexed Y, absolute bit relative, and
stack pointer relative indirect indexed Y.
DIRECT PAGE REGISTER (DPR)
Direct page register (DPR) is a 16-bit register. Its contents is used
as the base address of a 256-byte direct page area. The direct
page area is allocated in bank 0, but when the contents of DPR is
FF01
16
or greater, the direct page area spans across bank 0
16
and
bank 1
16
. All direct addressing modes use the contents of the di-
rect page register (DPR) to generate the data address. If the
low-order 8 bits of the direct page register (DPR) is “00
16
”, the
number of cycles required to generate an address is minimized.
Normally the low-order 8 bits of the direct page register (DPR) is
set to “00
16
”.
PROCESSOR STATUS REGISTER (PS)
Processor status register (PS) is an 11-bit register. It consists of a
flag to indicate the result of operation and CPU interrupt levels.
Branch operations can be performed by testing the flags C, Z, V,
and N.
The details of each processor status register bit are described
below.
1. Carry flag (C)
The carry flag contains the carry or borrow generated by the ALU
after an arithmetic operation. This flag is also affected by shift and
rotate instructions. This flag can be set and reset directly with the
SEC and CLC instructions or with the SEP and CLP instructions.
2. Zero flag (Z)
This zero flag is set if the result of an arithmetic operation or data
transfer is zero and reset if it is not. This flag can be set and re-
set directly with the SEP and CLP instructions.
3. Interrupt disable flag (I)
When the interrupt disable flag is set to “1”, all interrupts except
watchdog timer, DBC, and software interrupt are disabled. This
flag is set to “1” automatically when there is an interrupt. It can be
set and reset directly with the SEI and CLI instructions or SEP and
CLP instructions.
4. Decimal mode flag (D)
The decimal mode flag determines whether addition and subtrac-
tion are performed as binary or decimal. Binary arithmetic is
performed when this flag is “0”. If it is “1”, decimal arithmetic is
performed with each word treated as two or four digit decimal.
Arithmetic operation is performed using four digits when the data
length flag m is “0” and with two digits when it is “1”. (Decimal op-
eration is possible only with the ADC and SBC instructions.) This
flag can be set and reset with the SEP and CLP instructions.
相關PDF資料 |
PDF描述 |
|---|---|
| M37702S1BFP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2A | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2B | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2AXXXFP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2A-278FP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37702S1BFP | 制造商:Renesas Electronics Corporation 功能描述: |
| M37702S1LGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S1LHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S4AFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S4BFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。