- 您現在的位置：買賣IC網 > PDF目錄370847 > M37702S1AFP (Mitsubishi Electric Corporation) Single Chip 16 Bits CMOS Microcomputer(16位單片機) PDF資料下載
參數資料
| 型號： | M37702S1AFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| 中文描述： | 單片微機16位的CMOS（16位單片機） |
| 文件頁數： | 26/59頁 |
| 文件大?。?/td> | 811K |
| 代理商： | M37702S1AFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
26
MITSUBISHI MICROCOMPUTERS
M37702M2AXXXFP, M37702M2BXXXFP
M37702S1AFP, M37702S1BFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Fig. 31
Pulse period measurement mode operation (example of measuring the interval between the falling edge to next falling one)
After the contents of the counter is transferred to the reload regis-
ter, an interrupt request signal is generated and the interrupt
request bit in the timer Bi interrupt control register is set. However,
no interrupt request signal is generated when the contents of the
counter is transferred first time to the reload register after the
count start flag is set to “1”.
When bit 3 is “1”, the pulse width measurement mode is selected.
Pulse width measurement mode is similar to pulse period mea-
surement mode except that the clock is counted from the fall of the
TBi
IN
pin input signal to the next rise or from the rise of the input
signal to the next fall as shown in Figure 32.
When timer Bi is read, the contents of the reload register is read.
Note that in this mode, the interval between the fall of the TBi
IN
pin
input signal to the next rise or from the rise to the next fall must be
at least two cycles of the timer count source.
Timer Bi overflow flag which is bit 5 of time Bi mode register is set
to “1” when the timer Bi counter reaches 0000
16
.
This flag is cleared by writing to corresponding timer Bi mode reg-
ister. This bit is set to “1” at reset.
Fig. 32 Pulse width measurement mode operation
Selected clock
source f
i
TBi
IN
Reload register
←
Counter
Counter
←
0
Count start flag
Interrupt request signal
Selected
clock source fi
TBi
IN
Reload register
←
Counter
Counter
←
0
Count start
flag
Interrupt
request signal
相關PDF資料 |
PDF描述 |
|---|---|
| M37702S1BFP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2A | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2B | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37702M2AXXXFP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2A-278FP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37702S1BFP | 制造商:Renesas Electronics Corporation 功能描述: |
| M37702S1LGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S1LHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S4AFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S4BFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。