- 您現在的位置：買賣IC網 > PDF目錄370847 > M37702M2BXXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37702M2BXXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單片16位CMOS微機 |
| 文件頁數： | 40/59頁 |
| 文件大?。?/td> | 811K |
| 代理商： | M37702M2BXXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
40
MITSUBISHI MICROCOMPUTERS
M37702M2AXXXFP, M37702M2BXXXFP
M37702S1AFP, M37702S1BFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Fig. 51 Processor mode register bit configuration
PROCESSOR MODE
The bits 0 and 1 of processor mode register as shown in Figure 51
are used to select any mode of single-chip mode, memory expan-
sion mode, microprocessor mode, and evaluation chip mode.
Ports P3 to P0 and a part of port P4 are used as address, data,
and control signal I/O pins except in single-chip mode.
Figure 52 shows the functions of ports P4 to P0 in each mode.
The external memory area changes when the mode changes.
Figure 53 shows the memory map for each mode.
Refer to Figure 1 for the memory map of the single-chip mode.
The external memory area can be accessed except in single-chip
mode. The accessing of the external memory is affected by the
BYTE pin and the bit 2 (wait bit) of processor mode register.
These will be described next.
BYTE pin
When accessing the external memory, the level of the BYTE pin is
used to determine whether to use the data bus as 8-bit width or
16-bit width.
The data bus width is 8 bits when the level of the BYTE pin is “H”
and port P2 becomes the data I/O pin.
The data bus width is 16 bits when the level of the BYTE pin is “L”
and ports P1 and P2 become the data I/O pins.
When accessing the internal memory, The data bus width is al-
ways 16 bits regardless of the BYTE pin level.
An exclusive mode in the evaluation chip mode allows the BYTE
pin level to be set to 2·V
CC
. In this case, the operation is slightly
different from the above. This is described in the evaluation chip
mode section.
Clock
φ
1
output selection bit
0 : No
φ
1
output
1 :
φ
1
output
Processor mode bit
0 0 : Single-chip mode
0 1 : Memory expansion mode
1 0 : Microprocessor mode
1 1 : Evaluation chip mode
Wait bit
0 : Wait
1 : No Wait
Software reset bit
Reset occurs when this bit is set to 1
Interrupt priority resolusion time selection bit
0 0 : Select 1/f (X
IN
)
14
0 1 : Select 1/f (X
IN
)
8
1 0 : Select 1/f (X
IN
)
4
Test mode bit
This bit must be "0"
7 6 5 4 3 2
0
1
0
Processor mode register
Address
5E
16
相關PDF資料 |
PDF描述 |
|---|---|
| M37702M2L-249HP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S1LGP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37708S1LGP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702S1LHP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37708S1LHP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37702M2B-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2L | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2L249HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2L-249HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37702M2L-265HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。