參數資料
型號： M37640E8FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 42/96頁
文件大?。?/td> 1477K
代理商： M37640E8FP
42
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Fig. 1.42. UART Mode Register (U1MOD, U2MOD)
Fig. 1.43. UART Control Register (U1CON, U2CON)
LE1
PEN
PMD
STB
PS1
PS0
CLK
MSB
7
LSB
0
Address: 0030
16
,0038
16
Access: R/W
Reset: 00
16
LE0
1.19.1 UART Mode Register (UxMOD)
UxMOD defines data formats and selects the clock to
be used (see Figure 1.42).
1.19.2 UART Control Register (UxCON)
The UxCON specifies the initialization and enabling of a
transmit/receive process (see Figure 1.43). Data can
be read from and written to the Control Register.
CLK
UART Clock Selection Bit (bit 0)
0:
1: SCSGCLK
Internal Clock Prescaling Selection Bits (bits 2,1)
Bit 2
Bit 1
0
0: Division by 1
0
1
1
Stop Bits Selection Bit (bit 3)
0: 1
1: 2
Parity Selection Bit (bit 4)
0: Even
1: Odd
Parity Enable Bit (bit 5)
0: Off
1: On
Uart Character Length Selection Bits (bits 7,6)
Bit 7
Bit 6
0
0
1
1
PS1,0
1: Division by 8
0: Division by 32
1: Division by 256
STB
PMD
PEN
LE1,0
0: 7 bits/character
1: 8 bits/character
0: 9 bits/character
1: Reserved
AME
CTS_SEL
TIS
RIN
TIN
REN
TEN
MSB
7
LSB
0
Address: 0033
16
,003B
16
Access: R/W
Reset: 00
16
RTS_SEL
TEN
Transmission Enable Bit (bit 0)
0: Disable the transmit process
1: Enable the transmit process. If the transmit process is disabled (TEN
cleared) during transmission, the transmit will not stop until completed.
Receive Enable Bit (bit 1)
0: Disable the receive process
1: Enable the receive process. If the receive process is disabled (REN
cleared) during reception, the receive will not stop until completed.
Transmission Initialization Bit (bit 2)
0: No action
1: Resets the UART transmit status register bits as well as stopping the
transmission operation. The TEN bit must be set and the transmit
buffer reloaded in order to transmit again. The TIN is automatically
reset one cycle after Tin is set.
Receive Initialization Bit (bit 3)
0: No action
1: Clears the UART receive status flags and the REN bit. If RIN is set
during receive in progress, receive operation is aborted. The RIN bit
is automatically reset one cycle after RIN is set.
Transmit Interrupt Source Selection Bit (bit 4)
0: Transmit interrupt occurs when the Transmit Buffer Empty flag is set.
1: Transmit interrupt occurs when the Transmit Complete flag is set.
Clear-to Send (CTS) Enable Bit (bit 5)
0: CTS function is disabled. P8
6
(or P8
) is used as GPIO pin.
1: CTS function is enabled. P8
(or P8
2
) is used as CTS input.
Request-to-Send (RTS) Enable Bit (bit 6)
0: RTS function is disabled, P8
7
(or P8
) is used as GPIO pin.
1: RTS function is enabled, P8
(or p8
3
) is used as RTS output.
UART Address Mode Enable Bit (bit 7)
0: Address Mode disabled
1: Address Mode enabled
REN
TIN
RIN
TIS
CTS_SEL
RTS_SEL
AME
相關PDF資料
PDF描述
M37640E8FS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-XXXFP SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
M37640M8-111FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-126FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640E8 SINGLE-CHIP 8-BIT CMOS MICROCONTROLLER
相關代理商/技術參數
參數描述
M37640E8FS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37640M4T 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-111FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-126FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*