- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542M4-XXXHP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 PDF資料下載
參數資料
| 型號： | M37542M4-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| 封裝： | 6 X 6 MM, 0.50 MM PITCH, PLASTIC, WQFN-36 |
| 文件頁數： | 15/122頁 |
| 文件大?。?/td> | 1311K |
| 代理商： | M37542M4-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
7542 Group
Rev.3.03
Jul 11, 2008
Page 111 of 117
REJ03B0006-0303
3. Interrupt discrimination bit
Use an LDM instruction to clear to “0” an interrupt discrimination
bit.
LDM #%0000XXXX, $0B
Set the following values to “X”
“0”: an interrupt discrimination bit to clear
“1”: other interrupt discrimination bits
Ex.) When a key-on wakeup interrupt discrimination bit is cleared;
LDM #%00001110 and $0B.
4. Interrupt discrimination bit and interrupt request bit
For key-on wakeup, UART1 bus collision detection, A/D conver-
sion and Timer 1 interrupt, even if each interrupt valid bit (interrupt
source set register (address 0A16)) is set “0: Invalid”, each inter-
rupt discrimination bit (interrupt source discrimination register
(address 0B16)) is set to “1: interrupt occurs” when corresponding
interrupt request occurs.
But corresponding interrupt request bit (interrupt request registers
1, 2 (addresses 3C16, 3D16) is not affected.
Notes on Timers
1. When n (0 to 255) is written to a timer latch, the frequency divi-
sion ratio is 1/(n+1).
2. When a count source of timer X, timer A or timer B is switched,
stop a count of the timer.
Notes on Timer X
1. CNTR0 interrupt active edge selection
CNTR0 interrupt active edge depends on the CNTR0 active edge
switch bit (bit 2 of timer X mode register (address 2B16)).
When this bit is “0”, the CNTR0 interrupt request bit is set to “1” at
the falling edge of CNTR0 pin input signal. When this bit is “1”, the
CNTR0 interrupt request bit is set to “1” at the rising edge of
CNTR0 pin input signal.
2. Timer X count source selection
The f(XIN) (frequency not divided) can be selected by the timer X
count source selection bits (bits 1 and 0 of timer count source set
register (address 2A16)) only when the ceramic oscillation or the
on-chip oscillator is selected.
Do not select it for the timer X count source at the RC oscillation.
3. Pulse output mode
Set the direction register of port P14, which is also used as CNTR0
pin, to output.
When the TXOUT pin is used, set the direction register of port P03,
which is also used as TXOUT pin, to output.
4. Pulse width measurement mode
Set the direction register of port P14, which is also used as CNTR0
pin, to input.
Notes on Timer A, B
1. Setting of timer value
When “1: Write to only latch” is set to the timer A (B) write control
bit, written data to timer register is set to only latch even if timer is
stopped or operating. Accordingly, in order to set the initial value
for timer when it is stopped, set “0: Write to latch and timer simul-
taneously” to timer A (B) write control bit.
2. Read/write of timer A
Stop timer A to read/write its data in the following state;
XIN oscillation selected by clock division ratio selection bits (bits 7
and 6 of CPU mode register (address 3B16)), and the on-chip os-
cillator output is selected as the timer A count source.
3. Read/write of timer B
Stop timer B to read/write its data in the following state;
XIN oscillation selected by clock division ratio selection bits, the
timer A underflow is selected as the timer B count source, and the
on-chip oscillator output is selected as the timer A count source.
相關PDF資料 |
PDF描述 |
|---|---|
| M37542M2-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542M2-XXXHP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| M37542M2-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F4SP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37542F8HP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542M4-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542RSS | 功能描述:DEV EMULATION EVA CHIP FOR M3754 RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M37544 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37544G2AGP | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 8KB ROM 5V 32LQFP - Trays |
| M37544G2AGP#U0 | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction AVR® UC3 Introduction 標準包裝:2,500 系列:AVR®32 UC3 B 核心處理器:AVR 芯體尺寸:32-位 速度:60MHz 連通性:I²C，IrDA，SPI，SSC，UART/USART，USB 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:28 程序存儲器容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:32K x 8 電壓 - 電源 (Vcc/Vdd):1.65 V ~ 1.95 V 數據轉換器:A/D 6x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TQFP 包裝:帶卷 (TR) 配用:ATSTK600-TQFP48-ND - STK600 SOCKET/ADAPTER 48-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1101-ND - KIT DEV/EVAL FOR AVR32 AT32UC3B 其它名稱:AT32UC3B1128-AUR-NDAT32UC3B1128-AURTR |
發布緊急采購，3分鐘左右您將得到回復。