- 您現在的位置：買賣IC網 > PDF目錄370845 > M37516M6-A48KP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37516M6-A48KP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 15/54頁 |
| 文件大?。?/td> | 358K |
| 代理商： | M37516M6-A48KP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
15/54
M37516M6-XXXHP
GNOK-M37516M6-XXXHP-50
(MSETSU 2)
PA
GE
TIMERS
The M37516M6-XXXHP has four timers: timer X, timer Y, timer 1,
and timer 2.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “00
16
”, an un-
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency
which is selected by timer 12 count source selection bit. The out-
put of prescaler 12 is counted by timer 1 and timer 2, and a timer
underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts the count source selected by Timer count source
selection bit.
(2) Pulse Output Mode
The timer counts the count source selected by Timer count source
selection bit. Whenever the contents of the timer reach “00
16
”, the
signal output from the CNTR
0
(or CNTR
1
) pin is inverted. If the
CNTR
0
(or CNTR
1
) active edge selection bit is “0”, output begins
at “ H”.
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P2
7
( or port P4
0
) direction register to out-
put mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode,
except that the timer counts signals input through the CNTR
0
or
CNTR
1
pin.
When the CNTR
0
(or CNTR
1
) active edge selection bit is “0”, the
rising edge of the CNTR
0
(or CNTR
1
) pin is counted.
When the CNTR
0
(or CNTR
1
) active edge selection bit is “1”, the
falling edge of the CNTR
0
(or CNTR
1
) pin is counted.
(4) Pulse Width Measurement Mode
If the CNTR
0
(or CNTR
1
) active edge selection bit is “0”, the timer
counts the selected signals by the count source selection bit while
the CNTR
0
(or CNTR
1
) pin is at “H”. If the CNTR
0
(or CNTR
1
) ac-
tive edge selection bit is “1”, the timer counts it while the CNTR
0
(or CNTR
1
) pin is at “L”.
The count can be stopped by setting “1” to the timer X (or timer Y)
count stop bit in any mode. The corresponding interrupt request
bit is set each time a timer underflows.
Fig. 11 Structure of timer XY mode register
I
Note
When switching the count source by the timer 12, X and Y count
source bit, the value of timer count is altered in unconsiderable
amount owing to generating of a thin pulses in the count input
signals.
Therefore, select the timer count source before set the value to
the prescaler and the timer.
Fig. 12 Structure of timer count source selection register
Timer X count stop bit
0: Count start
1: Count stop
Timer XY mode register
(TM : address 0023
16
)
Timer Y operating mode bit
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR
active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer Y count stop bit
0: Count start
1: Count stop
b7
CNTR
active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
b0
Timer X operating mode bit
b1b0
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
Timer count source selection register
(TCSS : address 0028
16
)
b7
b0
Timer X count source selection bit
IN
CIN
0 : f(X
IN
)/16 (f(X
CIN
)/)/16 at low-speed mode)
Timer Y count source selection bit
0 : f(X
IN
)/16 (f(X
CIN
)/16 at low-speed mode)
1 : f(X
IN
)/2 (f(X
CIN
)/2 at low-speed mode)
Timer 12 count source selection bit
0 : f(X
IN
)/16 (f(X
CIN
)/16 at low-speed mode)
1 : f(X
CIN
)
Not used (returns “0” when read)
相關PDF資料 |
PDF描述 |
|---|---|
| M37516M6-A70HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A71HP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516RSS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A05 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37516M6-A70HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-A71HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6H-XXXKP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37516M6-XXXKP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。