- 您現在的位置：買賣IC網 > PDF目錄370845 > M37481M8T-297FP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37481M8T-297FP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 22/97頁 |
| 文件大?。?/td> | 1076K |
| 代理商： | M37481M8T-297FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
22
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
I
Note
The timer value cannot be read in this mode. A timer value can be
set while a timer operation stops (not under pulse width measure-
ment).
Since the timer latch of this mode becomes read only, do not per-
form a write operation during measurement.
The timer is set to “FFFF
16
” only when a timer underflows or when
the active edge of pulse width measurement is detected.
Accordingly, the timer value at a start of measurement depends on
the timer value provided before the start of measurement.
Figure 22 shows a timing diagram in the pulse width measurement
mode.
(5) Programmable Waveform Generation Mode
G
Mode Selection
This mode is selected by setting b2, b1 and b0 of TXM or TYM
to “100”.
G
Count Source Selection
The count source is f(X
IN
)/2, f(X
IN
)/8 or f(X
IN
)/16.
G
Interrupt
The underflow interrupt is the same as the timer event count
mode. The INT
0
interrupt request bit (b0) or INT
1
interrupt re-
quest bit (b1) of IREQ2 is set to “1” by detecting an active edge
of the INT pin.
G
Explanation of Operation
This operation is the same as that of the timer event count
mode, except that a timer outputs the level of the value set in
the output level latch (b4) of TXM or TYM from the CNTR
0
/
CNTR
1
pin each time the timer underflows. After the timer
underflows, if the values of the output level latch and timer latch
are changed, the timer can output an optional waveform from
the CNTR
0
/CNTR
1
pin. In this mode, set the port in common
with the CNTR
0
/CNTR
1
pin as an output port.
In this mode, if the trigger selection bit of TXM or TYM is set to
“1” and the count stop control bit of TXYCON is set to “0” (count
operation), a timer can be started concurrently with the occur-
rence of a trigger (input signal of INT
0
/INT
1
pin).
A timer starting trigger is set in the INT
0
edge selection bit (b0)
or INT
1
edge selection bit (b1) of EG. At “0”, the falling edge is
active. At “1”, the rising edge is active. When the count stop
control bit is “1” (count status), a timer is not started at the oc-
currence of a trigger.
Figure 23 shows a timing diagram in the programmable wave-
form generation mode.
(6) Programmable One-Shot Output Mode
G
Mode Selection
This mode is selected by setting b2, b1 and b0 of TXM or TYM
to “101”.
G
Count Source Selection
The count source is f(X
IN
)/2, f(X
IN
)/8 or f(X
IN
)/16.
G
Interrupt
The underflow interrupt is the same as the timer event count
mode. One-shot output trigger is set in the INT
0
edge selection
bit (b0) or INT
1
edge selection bit (b1) of EG. At “0”, the falling
edge is active. At “1”, the rising edge is active. The INT
0
inter-
rupt request bit (b0) or INT
1
interrupt request bit (b1) of IREQ2
is set to “1” by detecting an active edge of the INT pin.
G
Explanation of Operation
In case of One-shot Output “H”
(b2, b3 of EG = “0”)
While a timer operation stops
The output level of the CNTR
0
/CNTR
1
pin is initialized to “L” at
mode selection. Set the one-shot width in TXH, TXL, TYH and
TYL. While a timer operation stops, a trigger (input signal of
INT
0
/INT
1
pin) cannot occur.
While a timer operation is enabled
At detecting a trigger, a timer outputs “H” from the CNTR
0
/
CNTR
1
pin, and outputs “L” at a timer underflow.
In Case of One-shot Output “L”
(b2, b3 of EG = “1”)
While a timer operation stops
The output level of the CNTR
0
/CNTR
1
pin is initialized to “H” at
mode selection. Set the one-shot width in TXH, TXL, TYH and
TYL. While a timer operation stops, a trigger (input signal of the
INT
0
/INT
1
pin) cannot occur.
While a timer operation is enabled
At the detection of a trigger, a timer outputs “L” from the CNTR
0
/
CNTR
1
pin and outputs “H” at a timer underflow.
In this mode, set the port in common with the CNTR
0
/CNTR
1
pin as an output port.
I
Note
G
Input a trigger width over 250 ns to the INT
0
/INT
1
pin.
G
If the value of the CNTR
0
edge selection bit or CNTR
1
edge se-
lection bit is changed while one-shot output is enabled or
one-shot output occurs, the output level from the CNTR
0
/
CNTR
1
pin changes.
Figure 24 shows a timing diagram in the programmable one-
shot output mode.
相關PDF資料 |
PDF描述 |
|---|---|
| M37480E8SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481E8SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481E8SS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481E8T | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481MXT | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37481M8T-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37481M8T-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37481M8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37481M8-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 7470 SERIES |
| M37481MT-088FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。