- 您現在的位置：買賣IC網 > PDF目錄98005 > M37212EF-XXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37212EF-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 19/67頁 |
| 文件大?。?/td> | 4380K |
| 代理商： | M37212EF-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
MITSUBISHI MICROCOMPUTERS
M37212M4-XXXSP, M37212M6-XXXSP/FP
M37212EF-XXXSP/FP, M37212EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
and ON-SCREEN DISPLAY CONTROLLER
26
When the first-byte address data matches the slave address, the
AAS bit of the I2C status register (address 00D916) is set to “1.” After
the second-byte address data is stored into the I2C data shift register
(address 00D716), make an address comparison between the sec-
ond-byte data and the slave address by software. When the address
data of the 2 bytes matches the slave address, set the RBW bit of the
I2C address register (address 00D816) to “1” by software. This pro-
__
cessing can match the 7-bit slave address and R/W data, which are
received after a RESTART condition is detected, with the value of
the I2C address register (address 00D816). For the data transmis-
sion format when the 10-bit addressing format is selected, refer to
Figure 22, (3) and (4).
(10) Example of Master Transmission
An example of master transmission in the standard clock mode, at
the SCL frequency of 100 kHz and in the ACK return mode is shown
below.
Set a slave address in the high-order 7 bits of the I2C address
register (address 00D816) and “0” in the RBW bit.
Set the ACK return mode and SCL = 100 kHz by setting “8516” in
the I2C clock control register (address 00DB16).
Set “1016” in the I2C status register (address 00D916) and hold
the SCL at the “H” level.
Set a communication enable status by setting “4816” in the I2C
control register (address 00DA16).
Set the address data of the destination of transmission in the high-
order 7 bits of the I2C data shift register (address 00D716) and set
“0” in the least significant bit.
Set “F016” in the I2C status register (address 00D916) to generate
a START condition. At this time, an SCL for 1 byte and an ACK
clock automatically occurs.
Set transmit data in the I2C data shift register (address 00D716).
At this time, an SCL and an ACK clock automatically occurs.
When transmitting control data of more than 1 byte, repeat step
.
Set “D016” in the I2C status register (address 00D916). After this,
if ACK is not returned or transmission ends, a STOP condition
occurs.
(11) Example of Slave Reception
An example of slave reception in the high-speed clock mode, at the
SCL frequency of 400 kHz, in the ACK non-return mode and using
the addressing format is shown below.
Set a slave address in the high-order 7 bits of the I2C address
register (address 00D816) and “0” in the RBW bit.
Set the no ACK clock mode and SCL = 400 kHz by setting “2516”
in the I2C clock control register (address 00DB16).
Set “1016” in the I2C status register (address 00D916) and hold
the SCL at the “H” level.
Set a communication enable status by setting “4816” in the I2C
control register (address 00DA16).
When a START condition is received, an address comparison is
made.
When all transmitted addresses are “0” (general call)
AD0 of the I2C status register (address 00D916) is set to “1” and
an interrupt request signal occurs.
When the transmitted addresses match the address set in
ASS of the I2C status register (address 00D916) is set to “1” and
an interrupt request signal occurs.
In the cases other than the above
AD0 and AAS of the I2C status register (address 00D916) are
set to “0” and no interrupt request signal occurs.
Set dummy data in the I2C data shift register (address 00D716).
When receiving control data of more than 1 byte, repeat step .
When a STOP condition is detected, the communication ends.
相關PDF資料 |
PDF描述 |
|---|---|
| M37212EF-XXXSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP52 |
| M37221M6-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M37224M3-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37270MF-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64 |
| M37273MFH-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37212M4 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37212M4-054SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37212M4-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37212M6-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37212M6-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。