• <thead id="hwl2g"></thead>
    <small id="hwl2g"></small>
    <small id="hwl2g"></small>
  • <center id="hwl2g"><output id="hwl2g"></output></center>
    <small id="hwl2g"><ul id="hwl2g"><dd id="hwl2g"></dd></ul></small><thead id="hwl2g"><xmp id="hwl2g"><code id="hwl2g"></code>
    參數資料
    型號: M34519M6-XXXFP
    元件分類: 微控制器/微處理器
    英文描述: 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42
    封裝: 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
    文件頁數: 15/50頁
    文件大?。?/td> 1808K
    代理商: M34519M6-XXXFP
    22
    9571B–AT42–08/10
    AT42QT1111-MU/AT42QT1111-AU
    5.
    Control Commands
    5.1
    Introduction
    The QT1111 control commands are those commands that affect the device operation.
    The control commands are listed in Table 5-1 and are described individually in the following
    sections.
    Note:
    Commands are implemented immediately upon reception, so a suitable delay is
    required for the operation to be completed before communications can be
    re-established.
    5.2
    Send Setups (0x01)
    This command initiates the upload of the full settings table to the QT1111 (see Section 7 on
    When this command is received, the QT1111 stops key measurement and waits until 42 bytes of
    setup data have been received. Key acquisition will restart after all the setup data has been
    received.
    If enabled, a CRC check byte is transmitted (both ways) after the 42 bytes to confirm that they
    have been received correctly.
    If CRC checking is not enabled, it is recommended that the host request a dump of setup data
    from the QT1111, and confirms that the data correctly matches the data sent.
    The host must wait for at least 300 s for the operation to be completed before communications
    can be re-established.
    5.3
    Calibrate All (0x03)
    This command initiates the recalibration of all sensor keys.
    The host must wait for at least 300 s for the operation to be completed before communications
    can be re-established.
    Table 5-1.
    Control Commands
    Command
    Code
    Note
    Send Setups
    0x01
    Configures the device to receive setup data
    Calibrate All
    0x03
    Calibrates all keys
    Reset
    0x04
    Resets the device
    Sleep
    0x05
    Sleep (dead) mode
    Store to EEPROM
    0x0A
    Stores RAM setups to EEPROM
    Restore from EEPROM
    0x0B
    Copies EEPROM setups to RAM (automatically done at
    startup)
    Erase EEPROM
    0x0C
    Erases EEPROM setups
    Recover EEPROM
    0x0D
    Restores last EEPROM settings (after erase)
    Calibrate Key 'k'
    0x1k
    Calibrates one key (key k)
    相關PDF資料
    PDF描述
    M34519M8-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42
    M34519E8FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
    M34519M8-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42
    M34519M6-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42
    M34553M8H-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48
    相關代理商/技術參數
    參數描述
    M34519M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES
    M34-52 制造商:GAMEWELL-FCI 制造商全稱:GAMEWELL-FCI 功能描述:Three-Fold Fire Alarm Boxes and Transmitters
    M34524EDFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
    M34524M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
    M34524MC-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES