參數資料
型號: M34508G4GP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
封裝: 4.40 X 6.50 MM, 0.65 MM PITCH, PLASTIC, SSOP-20
文件頁數: 58/106頁
文件大小: 1059K
代理商: M34508G4GP
4508 Group
Rev.1.03
2009.07.27
page 53 of 140
REJ03B0148-0103
Fig. 46 State transition
Fig. 47 Set source and clear source of the P flag
Fig. 48 Start condition identified example using the SNZP in-
struction
Reset
(Note 1)
A
Operation source clock:
f(RING)
On-chip oscillator
B
Operation source clock: f(XIN)
Ceramic resonator: operating
C
Operation source clock: f(XIN)
RC oscillation
CRCK instruction no execution
CRCK instruction execution
POF instruction execution
(Note 5)
POF instruction execution
D
RAM back-up
f(RING): stop
f(XIN): stop
POF instruction execution
Operating state
Key-on wakeup
(Note 6)
Operating state
High-speed mode
(Note 5)
Internal mode
(Note 2)
(Note 3)
(Note 4)
(MR0)←0
(MR0)←1
Notes 1: Microcomputer starts its operation after counting f(RING) 120 to 144 times from system is released from reset.
2: When changing the operation source clock from f(RING) to f(XIN), first make the setting to enable f(XIN) oscillation (set MR1 to “0”),
allow the oscillation stabilization time to elapse using software, and then set the operation source clock to f(XIN) (set MR0 to “0”).
After this, stop f(RING) (set RG0 to “1”). (Do not start f(XIN) oscillation and change the operation source clock at the same time.)
3: When changing the operation source clock from f(XIN) to f(RING), first make the setting to enable f(RING) oscillation (set RG0 to “0”),
allow the oscillation stabilization time to elapse using software, and then set the operation source clock to f(RING) (set MR0 to “1”).
After this, stop f(XIN) (set MR1 to “1”). (Do not change the operation source clock and stop f(XIN) at the same time.)
4: After system is released from reset, the ceramic oscillation circuit is selected for the main clock f(XIN).
When the RC oscillation circuit is used, execute the CRCK instruction.
5: Continuous execution of the EPOF instruction and the POF instruction is required to go into the RAM back-up state.
6: Microcomputer starts its operation after counting f(RING) 120 to 144 times.
System returns to state A certainly when returning from the RAM back-up mode. The operation mode (system clock frequency divided)
also returns to the initial state (internal frequency divided by 8 mode) (registers RG and MR initialized).
However, the selected contents (CRCK instruction execution state) of f(XIN) oscillation circuit is retained.
S
R
Q
Power down flag P
POF
instruction
Reset input
● Set source
● Clear source
Reset input
EPOF
instruction
POF instruction
EPOF instruction +
+
Program start
P = “1”
?
Yes
Warm start
Cold start
No
SNTP
相關PDF資料
PDF描述
M34508G4H-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4HGP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34508G4FP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
M34518M2-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32
相關代理商/技術參數
參數描述
M34508G4GP#U0 功能描述:MCU 2/5V 4096 QZROM PB-FREE 20-S RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:720/4500 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO,I²C,LIN,UART/USART 外圍設備:DMA,LVD,POR,PWM,WDT 輸入/輸出數:27 程序存儲器容量:16KB(16K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤
M34508G4GP(#UO) 制造商:Renesas Electronics Corporation 功能描述:
M34508G4HFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34508G4HGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34508G4H-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER