參數資料
型號: M34501E4FP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
封裝: 5.30 X 12.60 MM, 1.27 MM PITCH, PLASTIC, SOP-20
文件頁數: 59/116頁
文件大?。?/td> 859K
代理商: M34501E4FP
4501 Group
Rev.3.01
2005.02.07
page 47 of 112
REJ03B0104-0301
Fig. 43 Switch to ceramic resonance/RC oscillation
Fig. 44 Handling of XIN and XOUT when operating on-chip oscillator
Fig. 45 Ceramic resonator external circuit
Fig. 46 External RC oscillation circuit
Execute the CMCK instruc-
tion in program.
Note: Externally connect a damping
resistor Rd depending on the
oscillation frequency.
(A feedback resistor is built-in.)
Use the resonator manu-
facturer’s recommended value
because constants such as ca-
pacitance depend on the
resonator.
(1) Selection of source oscillation (f(XIN))
The ceramic resonator or RC oscillation can be used for the source
oscillation of the MCU.
After system is released from reset, the MCU starts operation by
the clock output from the on-chip oscillator which is the internal os-
cillator.
When the ceramic resonator is used, execute the CMCK instruc-
tion. When the RC oscillation is used, execute the CRCK
instruction. The oscillation circuit by the CMCK or CRCK instruction
can be selected only at once. The oscillation circuit corresponding
to the first executed one of these two instructions is valid. Other os-
cillation circuit and the on-chip oscillator stop.
Execute the CMCK or the CRCK instruction in the initial setting rou-
tine of program (executing it in address 0 in page 0 is
recommended). Also, when the CMCK or the CRCK instruction is
not executed in program, the MCU operates by the on-chip oscilla-
tor.
(2) On-chip oscillator operation
When the MCU operates by the on-chip oscillator as the source os-
cillation (f(XIN)) without using the ceramic resonator or the RC
oscillator, connect XIN pin to VSS and leave XOUT pin open (Figure
44).
The clock frequency of the on-chip oscillator depends on the supply
voltage and the operation temperature range.
Be careful that variable frequencies when designing application
products.
(3) Ceramic resonator
When the ceramic resonator is used as the source oscillation
(f(XIN)), connect the ceramic resonator and the external circuit to
pins XIN and XOUT at the shortest distance. Then, execute the
CMCK instruction. A feedback resistor is built in between pins XIN
and XOUT (Figure 45).
(4) RC oscillation
When the RC oscillation is used as the source oscillation (f(XIN)),
connect the XIN pin to the external circuit of resistor R and the ca-
pacitor C at the shortest distance and leave XOUT pin open. Then,
execute the CRCK instruction (Figure 46).
The frequency is affected by a capacitor, a resistor and a micro-
computer. So, set the constants within the range of the frequency
limits.
*
Reset
On-chip oscillator
operation
CMCK instruction
CRCK instruction
Ceramic resonator valid
On-chip oscillator stop
RC oscillation stop
RC oscillation valid
On-chip oscillator stop
Ceramic resonator stop
4501
XIN
XOUT
*
Do not use the CMCK instruction
and CRCK instruction in program.
4501
XIN
XOUT
Rd
CIN
COUT
4501
XIN
XOUT
R
C
*
Execute the CRCK
instruction in program.
相關PDF資料
PDF描述
M34502M2-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO24
M34502M4-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO24
M34506M4-XXXFP 4-BIT, MROM, MICROCONTROLLER, PDSO20
M34506E4FP 4-BIT, OTPROM, MICROCONTROLLER, PDSO20
M34508G4HFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
M34501M2 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34501M2-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34501M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34501M4-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M34502E4 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER