- 您現在的位置：買賣IC網 > PDF目錄69010 > M34280M1-XXXFP 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | M34280M1-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| 封裝： | 0.300 INCH, 1.27 MM PITCH, PLASTIC, SOP-20 |
| 文件頁數： | 7/48頁 |
| 文件大小： | 605K |
| 代理商： | M34280M1-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
12
MITSUBISHI MICROCOMPUTERS
4280 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS
Table 4 Control registers related to timer
V12
V11
V10
Timer control register V1
Auto-control output by timer 1 is invalid
Auto-control output by timer 1 is valid
Carrier output (CARRY)
Bit 5 of watchdog timer (WDT)
Stop (Timer 1 state retained)
Operating
0
1
0
1
0
1
Carrier wave output auto-control bit
Timer 1 count source selection bit
Timer 1 control bit
at reset : 0002
W
at RAM back-up : 0002
Note: “W” represents write enabled.
(4) Timer 1 underflow flag (T1F)
Timer 1 underflow flag is set to “1” when the timer 1 underflows.
The state of this flag can be examined with the skip instruction
(SNZT1).
T1F flag is cleared to “0” when the next instruction is skipped
with a skip instruction.
(1) Control register related to timer
Timer control register V1
Register V1 controls the timer 1 count source and auto-
control function of carrier wave output from port CARR by
timer 1. Set the contents of this register through register A
with the TV1A instruction.
(2) Precautions
Note the following for the use of timers.
Count source
Stop timer 1 counting to change its count source.
Watchdog timer
Be sure that the timing to execute the WRST instruction in
order to operate WDT efficiently.
Writing to reload register R1
When writing data to reload register R1 while timer 1 is
operating, avoid a timing when timer 1 underflows.
(3) Timer 1
Timer 1 is an 8-bit binary down counter with the timer 1 reload
register (R1).
When timer is stopped, data can be set simultaneously in timer
1 and the reload register (R1) with the T1AB instruction.
When timer is operating, data can be set to only reload register
R1 with the T1AB instruction.
When setting the next count data to reload register R1 at
operating, set data before timer 1 underflows.
Timer 1 starts counting after the following process;
set data in timer 1,
select the count source with the bit 1 of register V1, and
set the bit 0 of register V1 to “1.”
Once count is started, when timer 1 underflows (the next count
pulse is input after the contents of timer 1 becomes “0”), the
timer 1 underflow flag (T1F) is set to “1,” new data is loaded
from reload register R1, and count continues (auto-reload
function).
When a value set in reload register R1 is n, timer 1 divides the
count source signal by n + 1 (n = 0 to 255).
Data can be read from timer 1 to registers A and B. When
reading the data, stop the counter and then execute the TAB1
instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| M34280M1-XXXGP | 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| M34280E1GP | 4-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| M34501M2-XXXFP | 4-BIT, MROM, 4.4 MHz, MICROCONTROLLER, PDSO20 |
| M34501E4FP | 4-BIT, OTPROM, 4.4 MHz, MICROCONTROLLER, PDSO20 |
| M34501M2-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34280M1-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTERS |
| M3428-100 | 制造商:MANHATTEN 功能描述:24AWG COMPUTER CABLE |
| M34282 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34282E2 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34282E2GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。