參數資料
型號: M29DW128F60NF6T
廠商: 意法半導體
英文描述: 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
中文描述: 128兆位(16Mb的x8或和8Mb x16插槽,多行,頁,引導塊)3V電源,快閃記憶體
文件頁數: 38/93頁
文件大?。?/td> 719K
代理商: M29DW128F60NF6T
6 Command Interface
M29DW128F
38/93
the Read mode where commands issued to the Boot Block Address space will address the
Boot Blocks.
Note that when the device is in the Extended Block mode, the V
PP
/WP pin cannot be used for
fast programming and the Unlock Bypass mode is not available.
The Extended Block cannot be erased, and can be treated as one-time programmable (OTP)
memory. In Extended Block mode only array cell locations (Bank A) with the same addresses
as the Extended Block are not accessible. In Extended Block mode dual operations are allowed
and the Extended Block physically belongs to Bank A.
In Extended Block mode, Erase, Chip Erase, Erase Suspend and Erase resume commands are
not allowed.
To exit from the Extended Block mode the Exit Extended Block command must be issued.
The Extended Block can be protected by setting the Extended Block Protection Bit to ‘1’;
however once protected the protection cannot be undone.
6.3.2
Exit Extended Block command
The Exit Extended Block command is used to exit from the Extended Block mode and return
the device to Read mode. Four Bus Write operations are required to issue the command.
6.3.3
Set Extended Block Protection Bit command
The Set Extended Block Protection Bit command programs the Extended Block Protection bit to
‘1’ thus preventing the second section of the Extended Block from being programmed.
A Read/Reset command must be issued to abort a Set Extended Block Protection Bit
command.
Six successive steps are required to issue the Set Extended Block Protection Bit command.
1.
The command starts with two unlock cycles.
2.
The third Bus Write cycle sets up the Set Extended Block Protection Bit command.
3.
The fourth Bus Write Cycle programs the Extended Block Protection bit to ‘1’.
4.
The last two cycles verify the value programmed at the Extended Block Protection bit
address: if bit DQ0 of Data Inputs/Outputs is set to ’1’, it indicates that the Extended Block
Protection bit has been successfully programmed. If DQ0 is ‘0’, the Set Extended Block
Protection Bit command must be issued and verified again.
6.3.4
Verify Extended Block Protection Bit command
The Verify Extended Block Protection Bit command reads the status of the Extended Block
Protection bit on bit DQ0 of the Data Inputs/Outputs. If DQ0 is ‘1’, the second section of the
Extended Block is protected from program operations.
6.3.5
Password Program command
The Password Program Command is used to program the 64-bit Password used in Password
Protection mode.
Four cycles are required to program the Password:
1.
The first two cycles are unlock cycles.
2.
The third cycle issues the Password Program command.
相關PDF資料
PDF描述
M29DW128F60ZA1 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
M29DW128F60ZA1E 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
M29DW128F60ZA1F 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
M29DW128F60ZA1T 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
M29DW128F60ZA6 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory
相關代理商/技術參數
參數描述
M29DW128F60ZA1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
M29DW128F60ZA1E 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
M29DW128F60ZA1F 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
M29DW128F60ZA1T 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
M29DW128F60ZA6 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory