- 您現在的位置：買賣IC網 > PDF目錄224124 > M27C256B-15C3TR (STMICROELECTRONICS) 32K X 8 OTPROM, 150 ns, PQCC32 PDF資料下載
參數資料
| 型號： | M27C256B-15C3TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 32K X 8 OTPROM, 150 ns, PQCC32 |
| 封裝： | LEAD FREE, PLASTIC, LCC-32 |
| 文件頁數： | 24/24頁 |
| 文件大?。?/td> | 205K |
| 代理商： | M27C256B-15C3TR |
M27C256B
Device operation
2.4
System considerations
The power switching characteristics of Advance CMOS EPROMs require careful decoupling
of the devices. The supply current, ICC, has three segments that are of interest to the system
designer: the standby current level, the active current level, and transient current peaks that
are produced by the falling and rising edges of E. The magnitude of this transient current
peaks is dependent on the capacitive and inductive loading of the device at the output. The
associated transient voltage peaks can be suppressed by complying with the two line output
control and by properly selected decoupling capacitors. It is recommended that a 0.1F
ceramic capacitor be used on every device between VCC and VSS. This should be a high
frequency capacitor of low inherent inductance and should be placed as close to the device
as possible. In addition, a 4.7F bulk electrolytic capacitor should be used between VCC and
VSS for every eight devices. The bulk capacitor should be located near the power supply
connection point. The purpose of the bulk capacitor is to overcome the voltage drop caused
by the inductive effects of PCB traces.
2.5
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27C256B are in the
"1" state. Data is introduced by selectively programming "0"s into the desired bit locations.
Although only "0"s will be programmed, both "1"s and "0"s can be present in the data word.
The only way to change a '0' to a '1' is by die exposure to ultraviolet light (UV EPROM). The
M27C256B is in the programming mode when VPP input is at 12.75V, G is at VIH and E is
pulsed to VIL. The data to be programmed is applied to 8 bits in parallel to the data output
pins. The levels required for the address and data inputs are TTL. VCC is specified to be
6.25V ± 0.25 V.
2.6
PRESTO II programming algorithm
PRESTO II Programming Algorithm allows to program the whole array with a guaranteed
margin, in a typical time of 3.5 seconds. Programming with PRESTO II involves the
application of a sequence of 100s program pulses to each byte until a correct verify occurs
(see Figure 4.). During programming and verify operation, a MARGIN MODE circuit is
automatically activated in order to guarantee that each cell is programmed with enough
margin. No overprogram pulse is applied since the verify in MARGIN MODE provides
necessary margin to each programmed cell.
相關PDF資料 |
PDF描述 |
|---|---|
| M27C256B-15XB6 | 32K X 8 OTPROM, 150 ns, PDIP28 |
| M27C512-45XN1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M27C512-60F1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M27C512-70XC1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M28754/14-01 | 20 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27C256B-15C6 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C256B15F1 | 制造商:STMicroelectronics 功能描述:IC EPROM 256KBIT 150NS DIP-28 |
| M27C256B-15F1 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C256B-15F1 | 制造商:STMicroelectronics 功能描述:IC EPROM CMOS 256K 27C256 DIP28 |
| M27C256B-15F6 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
發布緊急采購，3分鐘左右您將得到回復。