- 您現在的位置：買賣IC網 > PDF目錄224124 > M27C256B-15C3TR (STMICROELECTRONICS) 32K X 8 OTPROM, 150 ns, PQCC32 PDF資料下載
參數資料
| 型號： | M27C256B-15C3TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 32K X 8 OTPROM, 150 ns, PQCC32 |
| 封裝： | LEAD FREE, PLASTIC, LCC-32 |
| 文件頁數： | 2/24頁 |
| 文件大小： | 205K |
| 代理商： | M27C256B-15C3TR |
Device operation
M27C256B
Figure 4.
Programming flowchart
2.7
Program inhibit
Programming of multiple M27C256Bs in parallel with different data is also easily
accomplished. Except for E, all like inputs including G of the parallel M27C256B may be
common. A TTL low level pulse applied to a M27C256B's E input, with VPP at 12.75V, will
program that M27C256B. A high level E input inhibits the other M27C256Bs from being
programmed.
2.8
Program Verify
A verify (read) should be performed on the programmed bits to determine that they were
correctly programmed. The verify is accomplished with G at VIL, E at VIH, VPP at 12.75V and
VCC at 6.25V.
2.9
Electronic signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27C256B. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27C256B, with VCC = VPP = 5V. Two identifier bytes may then be sequenced from the
device outputs by toggling address line A0 from VIL to VIH. All other address lines must be
held at VIL during Electronic Signature mode. Byte 0 (A0 = VIL) represents the manufacturer
code and byte 1 (A0 = VIH) the device identifier code. For the STMicroelectronics
M27C256B, these two identifier bytes are given in Table 3 and can be read-out on outputs
Q7 to Q0.
AI00760B
n = 0
Last
Addr
VERIFY
E = 100
s Pulse
++n
= 25
++ Addr
VCC = 6.25V, VPP = 12.75V
FAIL
CHECK ALL BYTES
1st: VCC = 6V
2nd: VCC = 4.2V
YES
NO
YES
NO
YES
NO
相關PDF資料 |
PDF描述 |
|---|---|
| M27C256B-15XB6 | 32K X 8 OTPROM, 150 ns, PDIP28 |
| M27C512-45XN1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M27C512-60F1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M27C512-70XC1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
| M28754/14-01 | 20 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27C256B-15C6 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C256B15F1 | 制造商:STMicroelectronics 功能描述:IC EPROM 256KBIT 150NS DIP-28 |
| M27C256B-15F1 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C256B-15F1 | 制造商:STMicroelectronics 功能描述:IC EPROM CMOS 256K 27C256 DIP28 |
| M27C256B-15F6 | 功能描述:可擦除可編程ROM 256K (32KX8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
發布緊急采購，3分鐘左右您將得到回復。