- 您現在的位置：買賣IC網 > PDF目錄377804 > M27C1001-15BTR (意法半導體) 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM PDF資料下載
參數資料
| 型號： | M27C1001-15BTR |
| 廠商： | 意法半導體 |
| 英文描述： | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| 中文描述： | 1兆位（128千位× 8）紫外線存儲器和OTP存儲器 |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 153K |
| 代理商： | M27C1001-15BTR |
Device description
M27C1001
8/24
2
Device description
Table 2
lists the operating modes of the M27C1001. A single power supply is required in
Read mode. All inputs are TTL levels except for V
PP
and 12V on A9 for Electronic Signature.
Table 2.
Note:
X = V
IH
or V
IL
, V
ID
= 12V ± 0.5V.
2.1
Read mode
The M27C1001 has two control functions, both of which must be logically active in order to
obtain data at the outputs. Chip Enable (E) is the power control and should be used for
device selection. Output Enable (G) is the output control and should be used to gate data to
the output pins, independent of device selection. Assuming that the addresses are stable,
the address access time (t
AVQV
) is equal to the delay from E to output (t
ELQV
). Data is
available at the output after a delay of t
GLQV
from the falling edge of G, assuming that E has
been low and the addresses have been stable for at least t
AVQV
-t
GLQV
.
2.2
Standby mode
The M27C1001 has a standby mode which reduces the supply current from 30mA to 100μA.
The M27C1001 is placed in the standby mode by applying a CMOS high signal to the E
input. When in the standby mode, the outputs are in a high impedance state, independent of
the G input.
2.3
Two-line output control
Because EPROMs are usually used in larger memory arrays, this product features a 2-line
control function which accommodates the use of multiple memory connection. The two line
control function allows:
the lowest possible memory power dissipation,
complete assurance that output bus contention will not occur.
●
●
For the most efficient use of these two control lines, E should be decoded and used as the
primary device selecting function, while G should be made a common connection to all
devices in the array and connected to the READ line from the system control bus. This
Operating Modes
Mode
E
G
P
A9
V
PP
Q7-Q0
Read
V
IL
V
IL
X
X
V
CC
or V
SS
Data Out
Output Disable
V
IL
V
IH
X
X
V
CC
or V
SS
Hi-Z
Program
V
IL
V
IH
V
IL
Pulse
X
V
PP
Data In
Verify
V
IL
V
IL
V
IH
X
V
PP
Data Out
Program Inhibit
V
IH
X
X
X
V
PP
Hi-Z
Standby
V
IH
X
X
X
V
CC
or V
SS
Hi-Z
Electronic Signature
V
IL
V
IL
V
IH
V
ID
V
CC
Codes
相關PDF資料 |
PDF描述 |
|---|---|
| M27C1001-15CTR | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-15FTR | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-15NTR | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-15XBTR | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-15XCTR | 1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M27C1001-15C1 | 功能描述:可擦除可編程ROM 1M (128Kx8) 150ns RoHS:否 制造商:Maxim Integrated 類型: 存儲容量:1024 bit 組織:1 K x 1 接口類型: 工作電流:5 uA 編程電壓: 工作電源電壓:2.8 V to 6 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:TO-92 |
| M27C1001-15C1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-15C1X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-15C3TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-15C3X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
發布緊急采購，3分鐘左右您將得到回復。