- 您現在的位置：買賣IC網 > PDF目錄377800 > M-986-1R2P (CLARE INC) MFC Transceivers PDF資料下載
參數資料
| 型號： | M-986-1R2P |
| 廠商： | CLARE INC |
| 元件分類： | 信令電路 |
| 英文描述： | MFC Transceivers |
| 中文描述： | TELECOM, MF SIGNALING CIRCUIT, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 5/13頁 |
| 文件大小： | 520K |
| 代理商： | M-986-1R2P |
Signal Description
Signal
DIP
Pinout
PLCC
Pinout
I/O/Z
Description
Note:
Please see the following definitions: DIP = Dual In-line Package PLCC = Plastic Leaded Chip Carrier
D15-D8
18-11
13-17, 19-21
I/O/Z
D7-D0
19-26
22-28, 30
I/O/Z
TBLF
40
44
O
RBLE
1
2
O
HI/LO
2
3
BIO
9
10
RD
32
36
I/O
Unused. Leave open.
8-bit coprocessor latch.
Transmit buffer latch full flag.
Receive buffer latch empty flag
Latch byte select pin. Tie low.
Unused. Leave open.
Used by the external processor to read from the coprocessor
latch by driving the RD line active (low), thus enabling the output
latch to drive the latched data. When the data has been read, the
external device must bring the RD line high.
Unused. Leave open.
Microcomputer mode select pin. Tie low.
Coprocessor mode select pin. Tie low.
Reset input for initializing the device. When an active low is placed
on RS pin for a minimum of five clock cycles, RD and WR are
forced high, and the data bus (D7 through D0) goes to a high
impedance state. The serial port clock and transmit outputs also go
to the high impedance state.
Used by the external processor to write data to the coprocessor
port. To write data the external processor drives the WR line low,
places data on the data bus, and then drives the WR line high to
clock the data into the on-chip latch.
Watchdog signal. Toggles at least once every 15 milliseconds when
the processor is functioning properly. If the pin is not toggled at
least once every 15 ms, the processor is lost and should be reset.
System clock output (one-fourth crystal/CLKIN frequency,
nominally 5.12 MHz).
5V supply pin.
Ground pin.
Crystal output pin for internal oscillator. If an internal oscillator is
not used, this pin should be left unconnected.
Input pin to the internal oscillator (X2) from the crystal.
Alternatively, an input pin for the external oscillator (CLKIN).
Serial-port receive-channel inputs. 2.048 MHz serial data is received
in the receive registers via these pins. DR0 = channel 1; DR1 =
channel 2
Serial-port transmit-channel outputs. 2.048 MHz serial data is
transmitted from the transmit registers on these pins.These outputs
are in the high-impedance state when not transmitting.
I
I
EXINT
MC
MC/PM
RS
5
3
27
4
6
4
31
5
I
I
I
I
WR
31
35
I/O
XF
28
32
O
CLKOUT
6
7
O
V
CC
V
SS
X1
30
10
7
34
I
I
1, 12, 18, 29
8
O
X2/CLKIN
8
9
I
DR1 & DR0
33 & 29
37, 33
I
DX1 & DX0
36 & 35
40, 39
O
M-986-2R2
www.clare.com
5
Rev. 3
External Clock Option:
An external frequency source
can be used by injecting the frequency directly in
X2/CLKIN, with X1 left unconnected. The external fre-
quency injected must conform to the specifications list-
ed in the External Frequency specification Table on
page 7.
Flammability/Reliability Specifications
Reliability:
Flammability:
185 FITS failures/billion hours
Passes UL 94 V-0 tests
相關PDF資料 |
PDF描述 |
|---|---|
| M-986-2A1PL | MF Transceiver |
| M-986-2A1 | MF Transceiver |
| M-986-2A1P | MF Transceiver |
| M-986-2R2 | MFC Transceivers |
| M-986-2R2P | MFC Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M-986-1R2PL | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:MFC Transceivers |
| M9862 | 制造商:Tamura Corporation of America 功能描述: |
| M-986-2A1 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:MF Transceiver |
| M-986-2A1P | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 40xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| M-986-2A1PL | 功能描述:固態繼電器-PCB安裝 MF Transceiver, dual channel, 44xpin RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。